Dimmable 5.8G Microwave Motion Sensor Daylight Movement Detection
Constant Currant Output Daylight Detection Function Motion Sensor
Features of Sensor:
1. 5.8GHz microwave motion sensor with dimmable function.
2. Suitable for Tri-Proof light,battenlight and panel light.
3. Detached version flexible installation.
5. Constant current output.
5. 3 years warranty.
Product Description of Movement Detection Sensor:
| Operating voltage | 220-240VAC 50Hz/60Hz |
| Stand-by power | ≤1W(230VAC) |
| THD | <20% |
| Power factor | ≥0.9 |
| Efficiency | ≥82% (Max.) |
| Microwave frequency | 5.8GHz±75MHz |
| Microwave power | <0.3mW |
| Function setting mode | Dip swith/Remote control |
| Certificate | CE RoHS |
| Working temperature | -20°C~+50°C |
| IP grade | IP 20 |
ON/OFF Control Detection Area Hold Time Daylight Threshold Warranty
of 3 years
Stand-by Period Stand-by Dimming Level Remote Control Optional
Current
Mechanical structure of Motion Sensor:
| Detection area | 50%/100% |
| Hold time | 5s/90s/3min/10min |
| Daylight threshold | 15Lux/Disable |
| Stand-by dimming level | 10%/30% |
| Stand-by period | 0s/30s/10min/+∞ |
| Schema translation | Interaction |
Dimensional drawing (Unit: mm) of Motion Sensor:
HD01VR-4 Wire diameter 4mm, Standard Version Cable Length 480±10mm
(can be customized).
Wiring diagram of Motion Sensor:
| Input current | 0.15A(Max) |
| Input power | 30W (Max) |
| Output voltage | 28V~42V DC |
| Output current | 450mA/500mA/550mA/600mA±5% |
| Output control method | Turn off/dimmer |
Detection coverage of Motion Sensor:
This figure indicates the maximum distance at the highest mounting
height with 100% sensitivity.
Typical installation height 2.5-6m
| Detection range | Radius 4-7m/13.12-22.96ft |
| Detection angle | ≤150°(without glass) |
| Mounting height | 2.5-6m/8.2-19.68ft(ceiling mounted) |
Setting:
| Detection area(1) | | In this area, movement will be detected and able to trigger the
sensor. 100% detection area is also known as the strong sensitvity. |
| Hold time(2,3) | | The period of light keeping 100% brightness after moving objects
leave the detection area. |
| Daylight threshold(4) | | Definition of the ambient brightness; only when the ambient
brightness is lower than the preset specific lux amount, the sensor will work; when
it's preset as "disable", the sensor works everytime it detects motion regardless
the ambient brightness. |
| Stand-by dimming level(5,6) | | The definition of low output in the standby period. |
| Mode selection(7) | | Sensor mode on when the DIP switch is up; sensor mode off when the
DIP switch is down. |
| Stand-by period(8) | | The period of light keeping low output before it's completely
switched off. When it's preset as"∞“, the light always keep at low output if no
movement in the detection area and doesn't turn off. |
Application:
1. Automatically ON/OFF function:
Light on when detect movement and off after people leave at night.
Applications: Corridor, Staircase.
| With sufficient daylight,even when motion detected,light remains
OFF. |
| With insufficient daylight,when motion detected, light ON. |
| After the last detection and the present hold time elapsed, light
OFF. |
2. No daylight function
The daylight threshold is set to "Disable".
Light on when detect movement, After people leave, Light off after
stand-by period.
If the waiting time is +∞, the lamp is turned off and waits for the
next microwave trigger in the waiting brightness state.
| As soon as someone passes the detection area, the light will turn
on automatically. |
| When the person leaves the detection area, sensor into the delay
time, while holding
The light in the room should be 100% bright
Degrees. |
| After the delay time, the detection area has no one passes though
the detection area,the sensor enter the stand-by period,and the
light becomes dim. |
| After the stand-by period, there is no one passes through the
detection area,, the light goes out. |
3. Function Demo - Corridor function
| When the ambient light is sufficient, the light will not be on when
someone walks in the detection area. |
| When the ambient light is insufficient, the detection area detects
someone passing the light and turns it on. |
| At the end of the delay time, no one passes through the induction
zone, and the light becomes dark, entering the waiting time state. |
| At the end of the stand-by period, when the sensors no longer
detect movement, the lights automatically go out. |
Attention:
1. Please read the instructions carefully before using this product
and keep it well for all users to
read at any time.
2. The sensor should be installed by qualified electrician and
ensure power is off before the
installation.
3. We reserve the right to modify any incorrect text, image and
necessary technical parameters.
4. Any unauthorized modification is forbidden, otherwise all
guarantees will be immediately invalid.
Installation precautions:
1. Microwave sensor can be installed in any lamp except the one
with full metal shell.
2. The detected surface cannot be shielded by metal objects.
3. Make sure the microwave module is completely exposed outside.
4. The detection surface of the sensor module shall be installed
facing the detection area.
5. Should be kept away from the driver to avoid interference
generation and lamp flashing.
6. Wiring must be strictly in accordance with the wiring diagram to
avoid short circuit.
Application Environment:
1. Suitable for indoor installation to avoid false triggering due
to external factors such as rain, wind or tree swing.
2. Shall not be installed in the place with all four metal shelters
and small space (such as galvanized-iron roof ).
3. Shall note be mounted installation, so as to avoid false trigger
caused by the lamp itself shaking.
4. Shall not be installed next to large operating machines such as
ventilator/ceiling fan to avoid false triggering caused by machine
vibration.
User Notes:
1.Microwave can penetrate walls or glass thinner than 20cm and
attenuate if thicker than 20cm.
2. The driver voltage shall be stable and float within 10%.
3. Detection area will be affected by speed of motion, mounting
height and movement volume.
4. Conduct test on sunny days without the lampshade which will
affect the tested lux value.
HT30V-I.pdf
