Daewoo Excavator DH220 Excavator Bucket Teeth 2713 - 1217

2713 - 1217 Bucket Teeth Alloy Steel Casting Daewoo Excavator DH220

Specification

Description

1. Practice has proved that the wear rate of the outermost tooth of the bucket is about 30% faster than the innermost tooth during the use of the bucket teeth of the excavator. It is recommended to change the position of the bucket teeth abnormally after a period of time.
2. In the process of using bucket teeth, please choose bucket teeth according to different construction sites. For general excavation, weathered sand, surface media, etc., flat-head bucket teeth are used. RC-type bucket teeth are used for digging massive hard rocks, and L-type bucket teeth are generally used for digging massive coal seams. TL bucket teeth can increase the rate of coal lump generation. In actual use, users often like the universal RC type bucket teeth. It is recommended not to use RC type bucket teeth under special circumstances. It is best to use flat teeth, because RC type teeth will look like "fists" after a period of wear. Excavation resistance is large and power is wasted. The bottle-mouth bucket teeth always maintain a sharp surface during wear, reducing digging resistance and saving fuel.
3. The driving mode of the excavator driver is also very important to improve the utilization of bucket teeth. The driver should try not to retract the bucket when raising the boom. If the starting arm is raised while the bucket is retracted, this operation will cause the teeth to be torn from the top when the teeth are torn upwards, and the teeth will also be torn apart. Pay special attention to the coordination of actions during this operation. Some drivers often use too much force in the action of extending their arms to send their forearms, and quickly "knock" the bucket on the rock or force the bucket on the rock. This will break the teeth or easily hit the bucket into cracks, knocking the big and small arms.
4. The wear of the tooth seat is also very important to the service life of the bucket teeth of the excavator. It is recommended to replace the tooth seat after the tooth seat is worn by 10% to 15%, because there are excessively worn tooth seats and bucket teeth. The large gap changes the fit and stress point of the bucket tooth and the tooth seat, and the bucket tooth will break due to the change of the force point.
5. The excavator driver should pay attention to the digging angle when digging, and try to master it when digging. When digging down, the bucket teeth are perpendicular to the working surface, or the camber angle is not more than 120 degrees, so as not to break the bucket teeth due to excessive tilt. Also need to be careful not to dig the arm left and right under the condition of high resistance, this will cause the bucket teeth and the tooth seat to be broken due to excessive force on the left and right, because the mechanical design principle of most types of bucket teeth does not consider the left and right design The force.

More Models

Guangzhou Junhui Machinery Co., Ltd. is mainly engaged in the production and sales of various types of excavators, construction machinery main parts and hydraulic excavator seals, engine parts, hydraulic parts, air conditioning parts, chassis parts and wearing parts at home and abroad. The company has modern management, strong technical force, excellent service quality and wide sales range. Suitable for Komatsu, , Hitachi, Sumitomo, Kato, Daewoo, Hyundai, Kobelco, , Sany and other models.

Our Products Are As Follows

SEAL KIT: Boom Cylinder Seal Kit, Arm Cylinder Seal Kit, Bucket Cylinder Seal Kit, Control Valve Seal Kit, Main Pump Seal Kit, Travel Motor Seal Kit, Swing Motor Seal Kit, Rotary Center Joint Seal Kit, Regulator Seal Kit

Consumable Parts: Diamond Bucket Teeth, Welding Adapter

Engine parts: cylinder liner kits, valves, engine seal kits, crankshaft bushes, connecting rod bushes, crankshafts, camshafts, connecting rods, starter motors, alternators, high-pressure oil pumps, throttle motors, etc.
Hydraulic parts: main pump, travel motor, swing motor assembly and parts.

Air conditioning accessories: compressors, condensers, evaporators, expansion valves, dryers, control panels, filters, pipes, etc.
Chassis parts: track rollers, front idlers, sprockets, track shoes, track chains, etc.