Glass Sealing Rotating Table Glass Turning Table With Rollers On
Racks for insulating glass sealing
Usage of Rotating Table Machine For Turning Glass When Coating Sealants
Rotated sealant-spreading table is last preface of creation
insulation glass or act wall glass. It is a rotated table for draw
double group gum. It can proceed 90°Integral times rotated,also can
proceed face or contrary rotated. Revolve and vacuum sucker have
auto control equipment, it can combine glass size freedom choice
sucker and stretch arm control. Stretch arm of Special creation can
guarantee the top flat surface on a flat surface. This rotated
sealant-spreading table is rotated steady; Break down low, prop up
the stability. It is an ideal equipment to create insulating glass.
Main features of glass rotating table:
• Easy operating, simple and flexible
• It is used for fixing and rotating glass when manual coating the
outside of IG glass
• The middle sucker is suitable for small pieces of
glass,however,extra support frame is for large pieces of glass
Technical data of Glass Turning Table
| Power supply | 380V 50Hz |
| Total power | 0.37kw |
| Operating dimension | 1500*1500mm / |
| Dimension | 600*550*985mm
|
Maintenance :
1. New machine through revolving of a period of time after, should
open the plank, check whether each tight firmware loosen or not
moves, laying equal stress on the new tight.
2. Make to complete each time, want to clean dust and gum
clearances of the machine, combine to cover the turn over dish,
keep dust from falling into sucker.
3. Prop up set and prop up the pole should periodically draw the
lubrication grease, resisting rust.
4. The periodical check electricity connects whether line loose or
not moves, and connect the dependable of the ground.
Attention :
1. When tune up to prop up the tight in a bolt for and glass
contact even empress, must will prop up a top, prop up otherwise
the pole turns to move, prop up, the round escapes from the glass,
will produce the glass move the phenomenon.
2. Big sucker in usage, doing not want will enter the barometric
dint adjusts of over high, otherwise the vacuum a glass for too
bigger, being usage thickness is thinner, easy is ground the glass.
Main construction :
This machine include Adjust flat bottom,Prop up,Revolve to prop up
the device,Spread to move the device, spirit carries control
system, electric appliances control system and plank.
1.1 Revolve prop up the device
Revolve prop up the device include the prop up,prop up the
pole,prop up set,big sucker, small sucker.
1.2 Spread to move the device
This device consisted the Spread to move the deceleration
electrical engineering,decelerate machine and chain round.
1.3 Spirit carries control system
This system included the Spirit source processor, electromagnetism
valve, singled direction valve and vacuum occurrence machine, pass
the system control the matches of the size sucker.
Related products of LIJIANG GLASS
Rotary glue-coating table is auxiliary equipment of trough aluminum
insulating glass production line. It is used in conjunction with a
two-component glue dispenser. It is mainly used in the process of
filling the glass periphery with two-component glue after the
hollow glass covering is completed. Through the lifting, rotating,
positioning mechanism to achieve the positioning of the glass,
surrounding glue, removal and other processes. High degree of
automation, reliable performance and convenient operation. It has a
gas stop protection function to ensure that the gas plate does not
fall in the lifted position when the gas stops.
| |
Power supply | 380V 50Hz |
Total power | 0.37kw |
Dimension | 600mm*550mm*985mm |
Max. glass size | 2000*1500mm |
Min. glass size | 200*200mm |
Molding pressure | 0.5t |
Air pressure | 25Mpa |
Max. pressure | 0.5-0.8Kn |
Sharp Glass Edge Grinding Machine With Grinding Belts And Grinding
Wheels
Main feature of Edge finish machine LJKBM95
- It is used for polishing single glass, to prevent to hurt workman
from sharp glass edge
- It adopts type of ‘x’ to polish the up and down edge at the same
time
- Easy operating, simple and flexible
Technical data :
| Power supply | 380V 50Hz |
| Total power | 3kw |
| Dimension | 2000*1200*820mm |
Aluminum frame transfer machine LJSKJ02
Main feature of the spacer frame transfer machine
- Spacer frame transport
- Easy operating, simple and flexible
Technical data
| Power supply | 380V 50Hz |
| Total power | 0.18kw |
| Dimension | 2520*3012*3000mm |
Molecular sieve filling machine LJFGJ 03
Main feature
- Can effectively seal the desiccant,to keep dry
- Manual filling desiccant into spacer frame
- Recyclable
- Easy operating, simple and flexible
Technical data
| Power supply | 220V 50Hz |
| Total power | 1kw |
| Dimension | 2490*400*2200mm |
Cantilever crane LJXJ300 / 400 / 500 / 900 kg
| Max. load | 300kg (500kg is optional) |
| Rotated angle | 90° |
| Upright height | 3400mm or 3900mm |
| Rail length | 1000mm |
| Quantity of sucker | 2 or 4 |
| Air pressure | 0.5MPa-0.8MPa |
Company introduce:
JINAN LIJIANG AUTOMATION EQUIPMENT CO.,LTD
Address: Block B 1307, Green Square, Huaiyin District, Jinan, China
Tell : 0086 0531-85960498 Fax : 0086 0531-87562846
Salesperson: Hermione (+86 18353163989 / +86 13001733235)
Email: sales01@lijiang-glass.com
Website : www.lijiang-glass.com /
www.insulatingglassproductionline.com
After sales service:
a.Warranty: One year( The wearing parts and grinding tools are out
of this range) guarantee the perfect working condition by normally
replacing for wearing parts, electric parts and some other parts
under the proper operation.
b.LIJIANG has its own after service system. And it can be divided
into 3 situations.
① After the machine arriving customer’s factory,LIJIANG can send
its engineer to the customers’ factory for machine installation,
adjustment and personnel training for free.But the round-trip air
ticket, and accommodation will be born by the customer.
② During the warranty period (one year), if there is problems with
the equipment and the customer requests the LIJIANG engineer to
repair in the factory. The customer is responsible for the
round-trip air ticket , no maintenance fee and no spare parts cost
(except wearing parts).
③ Outside the warranty (one year), if the equipment appears
problems, the customer request LIJIANG to send engineers to the
factory for maintenance.The customer should be responsible for
round-trip air tickets and accommodation.Also customers need to pay
for the LIJIANG daily $150 as service and maintance costs, and all
parts must be completed paid before the delivery.
