A36 Hot Dipped Galvanized Grating

A36 Material ASTM A123 Standard Steel plant Hot Galvanized plain grating

plain grating Introduction:

Steel Bar Grating with bearing bars thicker than 3/16" is considered to be "Heavy Duty" and carries the designation prefix "Type HD". Available bar thicknesses are 1/4" (6.4mm) , 5/16" (7.9mm) and 3/8" (9.5mm) in either plain or serrated surface. Standard depths range from 1" (25mm) up to 4" (102mm), although larger sizes are available upon request.

Tru-Weld Heavy Duty Steel Bar Grating is commonly used for floor trenches and sump covers exposed to heavy equipment traffic. It is used extensively through out mining, power generation, highways, airfields, and on truck terminal loading docks and ramps. It is suitable for large single span conditions or where grating must be support extreme loads.

*All weights will increase by 5% when galvanized.

Tru-Weld bar grating is forge-welded, a system in which Qijie Grating was a pioneer. In this process the bearing bars and cross rods are permanently forged together by heat and pressure into a single unit construction, resulting in greater strength per pound than mechanical assembly methods. The twisted cross rods provide a non-slip walking surface. For applications where extremely slippery conditions prevail, Serrated bar grating offers a superior grip surface to the load bearing bars.

Bar grating types are specified by bearing bar spacing followed by cross rod spacing. In imperial measurements, bearing bar spacing is described in sixteenths of an inch. Therefore, Type 19 has bearing bar centers at 19/16 of an inch (or 1 3/16”). Type 15 has bearing bar centers at 15/16”. Type 11 is at 11/16” etc. The second number after the dash in the Type designation refers to the cross rod spacing. Cross rods are available in either 4” (standard) or 2” (special) spacings.

All bar grating Types may also be described in metric units. Again, the first number represents the bearing bar spacing on centers and the second number represents the cross rod spacing, both units measured in millimeters. Therefore, Type 30-102 Metric equals bearing bars at 30mm centers and cross rods at 102mm centers. This is the metric equivalent of Type 19-4.

Note: Although the special 2” (50mm) cross rod spacing does allow for less open space on the grating surface, it does not affect the load rating of the grating. The most economical and readily available choice for bar grating selection is Type 19-4 (Type 30-102 Metric).

Stainless Steel Grating

Stainless steel bar grating is a choice for corrosive environments such as chemical, food and hydro processing areas. It is available in welded and press locked as well as in many bearing bar sizes.

Materials: The most common material is Type 304 (SUS304), however, Type 316 (SUS316) or Type 316L (SUS316L) is also available. 304 stainless steel is the most popular type contains both chromium and nickel to provide excellent balance resistance and workability. 316 stainless steel is better corrosion, pitting resistance and higher strength at elevated temperatures than 304. 316L is extra low carbon variation of 316 to avoid carbide precipitation due to welding.

Uses: Stainless steel bar grating is mainly used in chemical industry, food processing, hydro processing and other industries .

Aluminum Grating

aluminum grating is designed to be a high-strength, low-weight product that uses an I-bar or rectangular bearing bar with cross rods hydraulically swaged under high pressure. Thus, giving you a rigid, virtually maintenance-free flooring product.

Similar to steel grating, aluminum grating can be pressure locked as an alternative to swage locked. This application process also allows the customer to choose a close mesh grate where certain special needs are to be met.

Open Mesh Grating

The open mesh steel grating is a flat panel with a light structure firmly welded together. It is widely used for industrial ladders, decking safety, ventilation ceilings and floors, platform and stair tread protection panels. The open spacing design instead of solid metals allows good ventilation, and easy flow of lighting and heat. The standard sheet size is 1m x 6m standard type (special size and American standard size are also customizable).

Qijie's parent company Anping Shenghe Metal Wire Mesh MFG Co., Ltd was set up in 1999. It is located in Anping, which has a reputation of "home of wire mesh" in China. Qijie is particularly established for export by Shenghe. The company implements "one team, two brands" management system and development strategy! We are a leading enterprise in this line with a registered capital of 500,000 US dollars, covering 40,000 square meters, has 3 plant areas, 30 stainless steel woven mesh machines, 18 welded wire mesh machines, 8 cutting and flattening mesh machines, and 2 automatic PVC coating lines, with annual amount of more than $ 20 million. The main products are stainless steel insect mesh, fence panels, chain link fence, gabion baskets, woven screening mesh, welded wire mesh, expanded metal mesh, perforated metal and various wire products. Our main aim is to ensure customer satisfaction by providing superior quality products at reasonable prices. We use meticulous quality control procedures and analysis in order to ensure our products meet the international standards. A combination of competitive prices, on-time delivery and quality guarantee will make us our customer's best choice.