405mm Brake Caliper Kit 7075 Aluminum

Jekit Auto Brake System 355/362/380/405mm Brake Disc Eight Pots

Install

1. Check whether the replaced brake pads are genuine accessories (i.e. supporting products), whether the integrity of the product packaging, anti-counterfeiting marks and packaging marks are consistent with the marks on the brake pads, and whether the product model is consistent with the contents of the certificate.

2. Before lifting the vehicle, open the cover containing brake oil and loosen the tire screws diagonally. If a simple jack is used for support, the jack shall be well supported and the wheels without replacing the brake pads shall be reinforced. Remove the tire, loosen the fastening screw of the tong body, check the screw and the sliding guide rod of the Tong, remove the sediment and oil stain on it, and apply lubricating oil for maintenance.

3. Remove the old brake pad and check the wear degree of the brake disc for groove and mess. If the brake disc is seriously worn (3mm deep on one side), it shall be replaced with a new brake disc with a cycle of 80000-120000 km, otherwise the wear of the newly replaced brake pad will be accelerated, the direction will shake during braking, and the braking force is too small.

4. When installing a new brake pad, the inside and outside shall be distinguished, and the friction surface of the brake pad shall face the brake disc to make the disc fit properly. Install the accessories and fasten the clamp body. Before tightening the tong body, use a tool (or special tool) to push the plug on the Tong back to facilitate the installation of the Tong in place. If the brake pad on the drum brake needs to be replaced, it is recommended to go to a professional maintenance factory for professional operation to avoid errors.

5. After the brake is installed, the tire should be reset. When installing the tire screws, tighten them diagonally to protect the tire and brake hub. At the same time, check whether the wear of the tread and edge is normal. It is best that the left and right wheels can be replaced regularly, which will help to prolong the service life of the tire. Before driving out of position, apply force to step on the brake until you feel that the brake has returned to the ideal state, and then you can drive out of position normally.

Refitting knowledge

First, what is a brake caliper? In short, the brake caliper is a part responsible for controlling the brake pads to clamp the brake discs in the wheels and slow down or stop the car. The brake caliper is very important. And how does the brake caliper control the brake pads to clamp the brake discs? When we step on the brake, we will apply pressure to the brake oil in the brake master cylinder, and the brake oil will transmit the pressure to each piston in the brake caliper, and push the piston in the caliper to control the brake pads to clamp the brake disc, so that we can stop the car.

In addition, many people will have the idea that "the more pistons in the brake caliper, the stronger the braking force". In fact, this idea is not completely wrong, because the more pistons, the larger the area of the brake pad, the larger the area, the higher the friction with the brake disc, and the better the braking force. However, the number of pistons does not help the braking force, and the brake master cylinder is the biggest help to the braking force. Xiaobian has just explained the processing steps of the brake system, and the brake piston will not work until the pressure input in the brake master cylinder, so more pistons don't mean anything, and the brake master cylinder is the key! So friends, do not blindly replace the brake caliper, and the brake master cylinder should also cooperate well!

Let's go back to the piston itself. In fact, there are different sizes of pistons. The more the number, the better, but depends on the size of the piston. For example, if you use six piston calipers, but all of them are small pistons, the braking area of a four piston calipers with a large piston may be larger than yours, and the braking force is naturally better than you, so you remember that the brake pistons have different sizes. In addition, so far, the number of brake card pistons is: single piston caliper, double piston caliper, four piston caliper, six piston caliper, eight piston caliper and ten piston caliper. In general, ordinary cars use single piston calipers or double piston calipers, while cars with better performance use four piston calipers. Most calipers with more than six pistons are modified cars and super running.

Next, will the position of the brake caliper affect the braking force? The answer is No. the position of the brake caliper is only an idea and design of the original factory, and will not increase the braking force. However, the position of the brake caliper determines the heat dissipation of the brake and the layout and installation space of the original chassis. The installation position of the brake caliper will also lead to different air circulation paths, and affect the heat dissipation of the caliper and the principle of aerodynamic dust removal. Therefore, in fact, the position of the brake caliper is also determined by.

In conclusion, the position of the brake caliper will not increase the braking force, but will only help heat dissipation and consider the layout of the chassis. The more pistons in the brake caliper, in fact, will not have much impact on the braking force. If you want to increase the braking force, you should match the brake caliper and the brake master cylinder well, so as to really improve the braking force.

Guangzhou Yuanxing Industrial Co.Ltd was established in 2017 and is located in Room 302, building 5, No. 7, Laowu street, Dongping village, Yongping street, Baiyun District, Guangzhou ,China. The location is very excellent and the transportation is convenient. We have very rich industry experience and is a trusted supplier. The company has production equipment and skilled front-line employees. Our boss has been engaged in the transformation of automobile braking system since 2011, have about 10 years of experience in this industry. Since 2017, we have set up our own factory, which can provide you with the best price and the best quality products. We specialize in producing aluminum alloy center cap and bracket, which can be customized according to different car models. Meanwhile we also sell complete set brake kit included brake calipers/brake disc rotors/brake pads/brake hose/aluminum center cap and brackets. Our products have strict quality control from the procurement of raw materials to the sale of finished products. Our company purpose is customer first, trying our best to meet the needs of customers. Our company's products are sold worldwide. With excellent quality and reasonable value, quality service, to win the trust and praise of our customers . Warmly welcome to visit our company and factory. We sincerely welcome friends from all over the world to visit our company and cooperate with us on the basis of long-term mutual benefits. We are looking forward to receiving your enquiry soon.