Item | Specification |
Power input | Voltage, frequency | D1: 90V DC to 400V DC or 110V±15% AC, 50/60Hz |
D2:150V DC to 450V DC or 220V±15% AC, 50/60Hz |
D3: 250V DC to 750V DC or 380V±15% AC, 50/60Hz |
T3: 350V DC to 750V DC or 380V±15% AC, 50/60Hz |
Allowable fluctuations | voltage unbalance rate:<3%; Frequency:±5%; aberration rate: as
IEC61800-2 required |
Power factor | ≥0.94(with DC reactor) |
Efficiency | ≥96% |
Output | Output voltage | Output under rated condition: 3 phase, 0～input voltage,
inaccuracy<5% |
Output frequency range | G type:0～600Hz |
Output frequency accuracy | Max frequency ±0.5% |
Overload capacity | G type: 150% rated current/1 min, 180% rated current/10s, 200%
rated current/0.5s |
Main control performance | Motor control mode | V/F without PG , VC without PG , VC with PG |
Speed control range | Vector control without PG, rated load 1:100;Vector control with PG,
rated load 1:1000; |
Steady speed accuracy | VC without PG: ≤2% rated synchronized speed; |
VC with PG: ≤0.05% rated synchronized speed |
Starting torque | VC without PG: when 0.5Hz, 150% rated torque; |
VC with PG: when 0Hz, 200% rated torque |
Torque response | VC without PG: ≤20ms; |
VC with PG: ≤10ms. |
Frequency accuracy | Digit setting: max frequency×±0.01%; |
Analog setting: max frequency×±0.2% |
Frequency resolution | Digital setting: 0.01Hz; |
Analog setting: maximum frequency × 0.05% |
product basic functions | DC braking capacity | Starting frequency:0.00～50.00Hz; Braking time:0.0～60.0s; |
Braking current:0.0～150.0% rated current |
Torque boost capacity | Auto torque upgrade 0.0%～100.0%; |
Manual torque upgrade 0.0%～30.0% |
V/F curve | 4 modes: one linearity torque characteristic curve ,one
self-setting V/F curve mode, one drop torque characteristic curve
(1.1- 2.0 powers),and square V/F curve mode. |
Acceleration/Deceleration curve | 2 modes: linear Acceleration/Deceleration and S curve
Acceleration/Deceleration. |
4 sets of ACC/DEC, time unit 0.01s selectable, longest time:
650.00s. |
Rated output voltage | Rely on power supply voltage compensate function, while motor rated
voltage is 100%, set it at the range of 50-100%(output can not over
input voltage). |
Voltage auto-adjustment | While power supply voltage fluctuates, it can auto-keep constant
output voltage. |
Auto energy-saving running | While under V/F control mode, according to load situation,
auto-optimize output voltage to save energy. |
Standard functions | PID control, speed track, power off restart, jump frequency,
upper/lower frequency limit control, program operation, multi-
speed, RS485, analog output, frequency impulse output. |
Frequency setting channels | Keyboard digital setting, keyboard potentiometer ,Analog
voltage/current terminal AI1,AI2, Communication given and
multi-channel terminal selection, Main and auxiliary channel
combination, expansion card, supporting different modes switch. |
Feedback input channel | Voltage/Current Terminal AI1, Voltage/Current Terminal AI12,
Communication |
given, pulse input X5. |
Running command channel | Operation panel given,external terminal given, communication given,
expansion card given. |
Input command signal | Start, stop, FWD/REV, JOG, multi-step speed, reset, ACC/DEC time
selection, frequency given channel selection, exterior fault alarm. |
Protective function | Overvoltage, under-voltage, current limit, over-current, overload,
electric thermal relay, overheat, overvoltage stall, data
protection, rapid speed protection, input/output phase failure
protection. |
Environment | Install place | altitude ≤ 1000m,above 1000m down the rated amount, each increase
of 100m down the rated mount of 1%;no condensation, ice ,rain,
snow, hail; solar radiation below 700W/㎡, air pressure 70-106 kPa. |
Temperature, humidity | -10 ～ + 50 ℃, derating above 40 ℃, maximum temperature 60 ℃
(no-load operation)5% to 95% RH (non-condensing) |
Vibration | When 9～200Hz, 5.9m/s2(0.6g) |
Storage temperature | -30 ～+60℃ |
Protection grade | IP20 |
Cooling method | Forced air cooling |
