Single face mill stand Corrugated Machine Spare Parts
Electric Shaftless Mill Roll Stand
Electrical clamping, lifting & shifting, pneumatic braking, with
expansion clip, electric appliances from Schneider
Technical Parameters:
1. Operation style of raw paper stand: electrically mechanical type
2. Range of clip paper(working width): 700 - 2000mm
3. Dia. of clip paper: Φ350mm - Φ1400mm
4. Max. weight of one side: 2000kg
5. Main stand shaft: Φ219mm
6. Total power: 5.2kw
Structural Features
1. The symmetric structure can be installed with two bundles of raw
paper at the same time used to change papers without halt.
2. This machine adopts the electric driver to finish lifting up or
down, clamping, loosening and centering the raw paper.
3. This machine adopts the pneumatic tension controller to adjust
the tensile force of raw paper.
4. The head of clip paper adopts expansion style.
5. The tension control adopts pneumatic braking, which can also be
on-line control together with Paper Splicer.
Main Bought-in Components and Raw Materials
1. Main stand shaft: high quality thick wall seamless steel pipe,
place of origin: Chengdu
2. Side wallboards: welded by high quality steel plates
3. Arms: casting HT200, place of origin: Hebei
4. Channels connected to main girder: 300mm, place of origin:
Angang Steel Group
5. Electric motors: cycloid motor of arms 1/35: 0.75kw, 4 sets,
intermittent working main shaft motor 1/59: 2.2kw, 1 set,
intermittent working
6. Electric Appliances: Schneider
7. Pneumatic components: Taiwan Airtac
8. Bearings: produced in Harbin, Luoyang or Wafangdian.
Φ280mm Fingerless Type Single Facer
A B C E flute, fingerless type, Φ280mm corrugated roller made of
high-quality alloy steel 48CrMo, chain transmission, electric
appliances from CHINT
Technical Parameters
Working width: 900-2000mm
Working air pressure: 0.6-0.9MPa
Total power: 5.5kw
Structural Features
1. This machine adopts the wind adsorption to keep the stability of
flutes.
2. The corrugated paper is adsorbed to the middle corrugated roller
to form a negative pressure zone of 180°and then to finish the
rolling of corrugation through the vacuum box by fan.
3. The width of suction slot of lower corrugated roller is not more
than 2.6mm, able to reduce the stripe mark on single side
corrugated cardboard.
4. The machine adopts chain transmission.
5. This machine adopts auto-cycle glue supply and pneumatic control
glue supply and return, making it be characterized by buffering
effect.
6. The glue roller surface is treated with special mesh nicking and
chrome-plating.
7. The upper and lower corrugated rollers are made of 48CrMo high
quality alloy steel. After heat-treatment, the hardness can be up
to HRC58-62 The surface is grinded and chrome plated.
8. Flute profile: A B C E flute.
Parameters of Main Parts
1. Upper corrugated roller: Φ268mm Lower corrugated roller: Φ268mm
Pressure Roller: Φ268mm 45# seamless steel pipe, quenched
2. Glue Roller: Φ210mm 45# seamless steel pipe, surface treated
with special mesh nicking and chrome-plating
3. Glue Scraping Roller: Φ120mm 20# seamless steel pipe
4. Pre-heating Roller: Φ268mm 20G Jigang steel
Raw Materials and Bought-in Components
1. Side Wallboards and base: casting HT200, place of origin: Hebei
2. Base of transmission parts: welded by channel
3. Electric Appliances: Schneider
4. Bearings: produced in Harbin, Luoyang or Wafangdian.
Sheet Cutter
Working width: 2000mm, electric appliances from CHINT
Technical Parameters
1. Working width: 2000mm
2. Cutting range: 390 - 2400mm
3. Cutting precision: ±3-5mm (at steady speed)
