Size Customizable Stainless Steel Pillow Plate Sheet For Heat Exchanger In Paper Pulp Black Liquor

Black Liquor Evaporation : Design and Operation

Requirement

The inherent complex composition of black liquor translates into several interdependent design requirements for the evaporators:
The evaporation plant must efficiently transfer heat for the evaporation of the black liquor.
It must do so while avoiding scale formation on the heat transfer surfaces.
The evaporation plant must also produce sufficiently cleancondensate fractions to satisfy the needs of the pulp mill and recausticizing area, thus greatly reducing the fresh water intake of the mill.
Volatile components and NCGs must be removed and conditioned for safe disposal via incineration.

Concentrators
A special of evaporator designs specifically engineered to address the two issues associated with the processing of black liquor at high concentrations:

1.Precipitation of supersaturated components from the liquor
At some point, typically around 50-55%TS,water soluble sulfate and carbonate sodium salts exceed their solubility limits and begin to precipitate from the black liquor being evaporated. The double salt burkeite is the first to precipitate in the concentration process while dicarbonate, another sodium double salt, reaches its solubility limit later on, around 60%TS.Control of this precipitation process is a crystallization problem, and achieving higher concentrations requires that evaporation equipment be designed as crystallizers to allow these salts to form in the bulk of the liquor,and not as scale on the heat transfer surfaces.

2. High liquor viscosity
As its concentration increases, black liquor rheological behavior changes from a Newtonian fluid to a pseudo- plastic fluid extremely viscous. Such high viscosities translate into poor heat transfer in concentrators (low Reynolds number hence low turbulence) but also represent an impediment to crystal growth within the bulk of the liquor. In addition,storage of the concentrated liquor, especially if well above 75%TS, may have to be in a pressurized tank in order to maintain the ability to pump the liquor to the boiler as well as proper spraying patterns. To address these viscosity issues, black liquor concentrators are typically operated at substantially elevated temperatures and proper control of the liquor temperature under varying operating conditions becomes a critical parameter of the design as a mere 20 °F increase in liquor temperature can translate into a viscosity reduction of 50% in some cases.
Operation at elevated temperatures enhances the breakdown of calcium-organic complexes present in the liquor and, as a result, the risk of precipitation of calcium carbonate on the heat transfer surfaces is substantially increased. Precipitation of other water insoluble compounds, such as silica and oxalate salts if present in the liquor, can also occur at these higher temperatures, increasing the risk of scaling of the concentrator units.
Heat treatment of the liquor prior to the concentrator can permanently reduce the liquor viscosity by thermal- cracking of the long lignin and other organic compounds responsible for the liquor viscosity. Such treatment typically takes place in a continuous reactor operated at high pressure and temperature (above 350°F). Over 30 min of residence time in the reactor must be provided to achieve maximum viscosity reduction.

Two types of black liquor concentrators are in use today and those can be broadly classified as Falling Film (FF) and Forced Circulation (FC)designs.

Mechanical Vapor Recompression MVR Evaporator consumption compared with traditional evaporation equipment calculated by evaporating 1T water

Falling Film Concentrator

Falling Film Concentrators are really an adaptation for high solids service of the FF evaporator design discussed above. By nature, FF concentrators, where evaporation takes place from a liquor film within the heating element result in high supersaturation levels being developed within the liquor. This can result in uncontrolled scale formation due to excessive crystal nucleation rather than gentle crystal growth.

Forced Circulation concentrator

Forced Circulation concentrators have been around since the 1950's and are well proven in black liquor service. The design consists ofa heat exchanger and a vapor/liquor flash chamber connected to each other through a recirculation loop.

Jiangsu Hanpu Mechanical Technology Co., Ltd. is a project engineering company jointly established by Jiangsu Zhongyi Environmental Technology Co., Ltd., FERREO A/S in Denmark, Shanghai Jiaotong University and Nanjing Kingreat Machinery Co., Ltd. The company's production base is located in the Huangqiao Industrial Zone of Taixing, covering an area of 300 acres. The companies involved are in the industry of new material, new energy, medicine, chemical, environmental protection, food, and beverage, etc.

The company has a national functional office and facilities as a scientific research bureau. The research center now has 5 doctor tutors, 8 professional engineers, 11 senior engineers, 42 engineers and 68 assistant engineers making it a leading specialized research bureau.

The company has various kinds of general (special) machinery devices including 480 sets and are the most developed working devices in the world such as: Toshiba CNC boring and milling machine imported from Japan, German Schiess CNC turning processing center, CNC fine plasma cutting machine imported from Germany, Laser cutting machine, CNC folding machine, CNC wire cutting and CNC shearing machine, etc.

The company's main projects include but are not limited to: MVR evaporation system, powder washing salt and vacuum salt production project, oil tank sludge cleaning project, landfill leachate treatment project, plant/animal oil processing production line, urban wastewater treatment project, various wastewater treatment projects, and CBD oil extraction production line. Technical support and transfer of API product technology package. The main products are centrifuge series, multi-effect and MVR evaporation and crystallization equipment, laser welding heat transfer board, lithium battery material mixing equipment, pressure vessel and titanium, zirconium, nickel, and other non-standard special equipment.

The company's sales network throughout the whole world, with a domestic sales market share of 50%, and exported to the United States, Canada, Germany, Spain, France, Switzerland, Sweden, Denmark, Australia, Brazil, Argentina, Chile, Colombia, Russia, Ukraine, Poland, Uzbekistan, Indonesia, Vietnam, Singapore, Malaysia, India, Japan, South Korea, Iran, South Africa, Nigeria, and Rwanda.

The company is an internationally competitive engineering company that integrates technical consulting, design, procurement, construction, installation and driving into one, providing engineering EPC general contract, project management, engineering supervision and other comprehensive, full-process services. The company is Committed to be the first and world-renowned technology and technology engineering company in Asia, providing cutting-edge technology and one-stop solutions for the world's industries.