High Accuracy Battery Operated Electromagnetic Flow Meter To
Measure Liquid
1.Working Principle
The principle of the sensor is based on Faraday’s law of
electromagnetic induction.It is installed a pair of detection
electrodes on the pipe wall,where the measurement pipe axis and
magnetic field lines are vertical. When the conductive liquid cuts
magnetic field lines and produces induced electromagnetic
force.Which can be measured by the two electrodes on the meter
pipe.The result can be calculated by formula: Induced electromotive
force,(flow signal)E=KBDV
E——Induced electromotive force,V；
K——meter constant；
B——Magnetic flux density,T；
D——Internal diameter of measuring pipe,m；
V——Average velocity of pipe section,m/s.
MLF Series Electromagnetic Flow Meter
Assume the volume of liquid as qv(m3/s),qv=πD2V/4),so in the
formula E=(4kB/πD)qv=kqv,K is meter constant,K=4kB/πD.
Actually, the electromagnetic flow meter consists of two parts,
transmitter and sensor, the measuring electrodes inspect the
electromotive force, and transmit to the converter, the converter
provides excitation current.E is usually called a flow signal,
after processing the flow signal by converter, output 4~20
mA/pulse(or frequency) signal which is proportional to the flow
rate, then the flow rate recording,adjusting can be achieved.
2. Quick Details
MLF electromagnetic flowmeter is explosion-proof design.
Function of low conductivity measurement.
There are nine languages options to meet the needs of different customers.
It has the function of self-regulation and self-examination.
Different outputs are optional: Hart,RS485 Profibus,4-20mA, frequency, pulse.
3. Specification
| MLF Type | Divided Type | Integrated Type | Explosive Proof Integrated Type | Battery Powered Type | Heat Energy Type |
| Accuracy | ±0.2% or ±0.5% |
| Pipeline Diameter | DN10-DN2000 | DN10-DN600 | DN25-DN2000 |
| Flange | GB, ANSI, JIS, BS, Others |
| Pressure | DN10-DN600 1.0 1.6 2.5 4.0MPa |
| DN700-DN2000 0.6 1.0 1.6MPa |
| Liner Material | CR, PTFE, PU, Hard Rubber, PFA, FEP(F46) |
| Conductivity | ≥5µs/cm(Please contact us if it is less than 5µs/cm) |
| Electrode | 316L SS, Hb, Ta, Ti, Hc, Tungsten Carbide, Others |
| Protection Class | IP65, IP66, IP67, IP68 |
| Medium Temperature | -25~180℃
(Please refer to liner material) | -25~80℃(Please refer to liner material) | -25~180℃
(Please refer to liner material) |
| Ambient Temperature for Accuracy Influence | <±0.1%/10℃ or <±0.25%/10℃ at the ambient temperature of -25~60℃ |
| Repetability | ≤±0.1% or ±0.25% |
| Analog Output Error | ≤±0.02mA |
| Velocity | 0.3~10m/s |
| Electrical connection | M20x1.5 Seal Cartridge, GB1/2, NPT1/2 |
| Output | 4-20mA, Pulse, RS485, Hart, Profibus |
4. Dimensional Sketches
a. Dimension of Converter
Divided Type
Integrated Type
Battery Powered Type
b. Dimension of Sensor
| Pipeline Diameter | Dimension |
| L | W | H |
| 15 | 160 | 95 | 130 |
| 20 | 160 | 105 | 137 |
| 25 | 160 | 115 | 150 |
| 32 | 160 | 135 | 160 |
| 40 | 200 | 145 | 175 |
| 50 | 200 | 160 | 185 |
| 65 | 200 | 180 | 205 |
| 80 | 200 | 195 | 215 |
| 100 | 250 | 215 | 235 |
| 125 | 250 | 245 | 275 |
| 150 | 300 | 280 | 300 |
| 200 | 350 | 335 | 355 |
| 250 | 400 | 400 | 405 |
| 300 | 500 | 455 | 460 |
| 350 | 500 | 515 | 520 |
| 400 | 600 | 575 | 580 |
| 450 | 600 | 635 | 630 |
| 500 | 600 | 710 | 685 |
| 600 | 600 | 835 | 795 |
| 700 | 700 | 905 | 910 |
| 800 | 800 | 1020 | 1030 |
| 900 | 900 | 1120 | 1120 |
| 1000 | 1000 | 1245 | 1250 |
| 1200 | 1200 | 1465 | 1470 |
5. Maintance
The electromagnetic flowmeter has a self-diagnostic function. In
addition to power supply and hardware circuit failures, the system
also alarms other failures in general use. These messages will give
corresponding prompts in the lower right corner of the screen.
1 Maintenance and repair
a) The sensor installation site should meet the requirements of
Section 4, please keep the housing tidy;
b) The transmitter should be placed in a clean, ventilated and dry
place;
c) It needs to be inspected every two years. For high-precision
users, the instrument needs to be submitted for review.
2 Transportation and storage
a) The instrument must be packaged before transportation, and be
handled with care when loading and unloading.
b) The storage place must be dry and ventilated to avoid corrosive
gases, and the ambient temperature should not be too low or too
high;
c) The storage time should not exceed three years.
3. Unpacking inspection
a) The package cannot be opened with a heavy hammer, be careful not
to damage the instrument
b) Check the contents carefully according to the packing list.
6.Company Profile
Melan Measurement & Control Instruments is located in Shanghai
City. It is a high-tech manufacturer specialized in the design,
development, manufacturing and sale of measurement and control
instruments.
Our products are widely used in various fields, including
electricity, chemical industry, metallurgy, brewing, oil and gas,
textile, water conservancy, environmential protection, etc.
We own independent-courtyard modemized manufacturing workshops and
an open office building. Melan has accumlated production and
management experience in instruments from European and American and
domestic famous companies.
We own first-class talent team, and all the products have reached
advanced level at home and abroad. We provide our customers with
complete and professional test control solutions and high-tech and
high-quality products.
Melan is your reliable friend and partner. We are willing to try
our best as dedication and perfection as motivation.
7.FAQ
Q: How long will you give me the reply?
A: We will contact you in 5 hours as soon as we can.
Q: What is the warranty of your prducts?
A: Our warranty is 12 months after the shipping date.
Q: What is the lead time of your products?
A: Normally our factory lead time is 10-12 working days.
Q: Can I OEM your products?
A: OEM and ODM customization are welcomed.
Q: What is your MOQ?
A: We have no MOQ limit, small quantity order is acceptable.
Q:What is the transport?
A: Express such as DHL, FedEx, UPS for freight prepaid, and we can
also use your own courier account to do the freight collect. For
more goods we can arrange by air or by sea.
