W01-R58-4043 Firestone Air Bags 4 1/2 X 1 DUNLOP SP 2008 Open Mouth
51mm
AIRSUSTECH 4 1/2 X 1 Single Convoluted Air Spring Specifications
❶Nut / Blind Nut
The Long Of The Nut:8 mm
Top Cover Plate Screw number:6pcsXM6-8MM
Bottom Cover Plate Screw number : 6pcsXM6-8MM
❷ Gas Hole / Air inlet / Air Fitting
Gas Hole / Air inlet : 3/8 BSP
❸ Cover Plate
Top Cover Plate Diameter: 93mm
Bottom Cover Plate Diameter: 93 mm
❹Rubber Bellows
In 0.7 M pa,Rubber Bellows Diameter : 135 mm
Rubber Bellows Natural Height :114 mm
❺ Bumper block / Buffer block
Without Bumper Block
❻ Girdle Hoop / Girdle Ring
Without Girdle Hoop
Description of AIRSUSTECH 4 1/2 X 1:
AIRSUSTECH 4 1/2 X 1 is produced by AIRSUSTECH factory. AIRSUSTECH
air spring 4 1/2 X 1 double scroll airbag can completely replace
W01-R58-4043 Firestone Air Bags; the technical parameters of
AIRSUSTECH 4 1/2 X 1 are the same as W01-R58-4043 Firestone Air
Bags, indicating AIRSUSTECH 4 1/2 X 1 gasScroll industrial air
springs will not use internal flexible parts of molded beads.The
number of rubber bellows is 25, and the flexible piece is connected
to the end of the bracket by clamping the material between the top
plate and the bottom plate, and then adjusting it to a suitable
diameter.
The drawing of 4 1/2 X 1;W01-R58-4050;DUNLOP SP 2334:
Rubber shock absorber airbag is a kind of curved capsule made of
rubber and network cable.
The end structure of the existing convoluted rubber shock absorber
airbags can be divided into three categories according to the
connection mode: one is the fixed flange connection type (G type),
and the two ends of the air spring have the largest edge size and
the convoluted bladder. The outer diameter is the same or slightly
smaller. After drilling several holes, use the flange ring and the
end plate to fasten the connection; the other type is the looper
flange connection type (H type), the size of the two ends of the
air spring is the largest than the curved bladder The outer
diameter is much smaller, no need to drill, a special flange ring
and an ordinary end plate are used to fasten the connection; the
third type is the self-sealing type (J type).
The two ends of the capsule need to be connected with two steel
plates to form a compressed air chamber. The rubber and network
cable itself does not provide the load bearing capacity, but is
completed by the compressed air filled into the capsule. The number
of convoluted sacs is usually 1 to 3 convoluted sacs, but it can
also be designed and manufactured to be 4 or more than 5 bends
according to the needs, and two air springs can also be used in
superposition under certain conditions.
The rubber shock absorber airbag is also called according to its
performance and characteristics: rubber air stroke regulator,
rubber air vibration isolator, two product names.
The Composition Of Industrial Convoluted Air Spring Element Has The
Following Aspects
❶Nut / Blind Nut – As well a permanent part of the Cover Plate
assembly. Provides an alternative to bolt installation system. It
is inside defect within the iron plate
❷ Gas Hole / Air inlet / Air Fitting – Most usually 1/4 N.P.T.
which provides the air entrance to the rubber bellows.
❸ Cover Plate - Curled up to more durable bellows design and the
largest quality control in the factory. Allows 100% of the leak
test before shipment.
❹Rubber Bellows - Air Bellows includes four layers of materials: an
inner layer, two layer cord - reinforced fabrics, and a cover.
Construction of a natural rubber provides – 65F functional
properties.
❺ Bumper block / Buffer block - Solid rubber or engineering plastic
device designed to prevent major damage to the vehicle or
suspension in the event of a sudden loss of air pressure in the
spring.
❻ Girdle Hoop / Girdle Ring - Molded wire-wound ring to provide
lateral stability of the complex type spring bellows.
