EO ETO Ethylene Oxide Sterilization Equipment For Low Temperature Sterilization

EtO Sterilization Cycle

There are at least three stages in a typical EtO sterilization cycle:

• Preconditioning
• Sterilization
• Aeration (Degassing)

Cycle time is usually more than 14 hours.

Preconditioning

Preconditioning prepares the chamber environment to meet the ideal conditions for temperature, pressure and humidity. First air is removed from the chamber to allow for gas penetration. A leakage test is performed, to ensure that staff and environment are safe. Next, some steam is injected into the chamber and humidifies the load, since EtO is only effective in a humid environment. The chamber is heated by either steam or hot water which is present in the jacket. Normally the jacket is kept at the same temperature 24/7 to minimize temperature fluctuations.

Sterilization

The second stage is the actual sterilization process. The EtO enters the chamber via evaporation with a certain amount of steam to keep the humidity level up as well as to make sure the EtO is reaching all parts of the load. When the required concentration in the chamber and load is achieved the actual sterilization stage starts. The lower the gas concentration in the chamber the longer is the sterilization time. As EtO is absorbed by many kinds of plastic materials it is important to keep the concentration at the right level. To achieve this EtO is sometimes added to the chamber after a while. It is of major importance to ensure the appropriate concentration level of EtO in the chamber to achieve effective and safe sterilization.

Aeration (Degassing)

Aeration is the most important and longest part of the EtO sterilization cycle. As mentioned, materials such as plastics and rubbers absorb gas and if applied to patients, the toxic gas could damage their body tissue! For this reason it is very important to have an excessive aeration stage to remove any remaining EtO gas and to allow absorbed gas to evaporate again from the sterilized items. This is done by circulating HEPA filtered air over the load at a temperature of 30°C to 50°C. This is sometimes done in the sterilizer’s chamber, but sometimes the sterilized items are placed in a special aeration cabinet. If the sterilized items are repositioned from the chamber to the aeration cabinet then strict safety precautions should be in place to prevent EtO gas exposure to the people who perform this function. A commonly used time period for this aeration treatment is 48 hours which results in a very slow instrument turnaround. A special infrastructure is required, with gas tight ventilation piping to the roof top or to a catalyzer. The sterilizer cannot use the hospital's ventilation system because it is too dangerous. The special ventilation piping has to be tested for gas leaks all the way as this is the only way to minimize the risks.

There are some advantages however. An EtO sterilizer can have a very large chamber, even up to 7m³. They are often used for the sterilization of large quantities of products that cannot be sterilized by steam. When gauze or non-woven materials like disposable gowning are manufactured they need to be sterilized before entering the hospital. These are often sterilized by EtO because steam will damage or deform these materials.

To summarize, EtO sterilization should be used only when another method is not appropriate.

Advantages of EtO are:

• Low temperature
• High efficiency – destroys microorganisms including resistant spores
• Large sterilizing volume/ chamber capacity
• Non corrosive to: plastic, metal and rubber materials

Disadvantages are:

• Excessively Long cycle
• Safety concerns - carcinogenic to humans
• Toxicity issues - toxic residues on surgical instruments and tubing
• Not recommended for flexible scope
• EtO is flammable
• Requires special room conditions, safety equipment and separate ventilation system
• Relatively high annual costs for maintenance, servicing and consumables

Technical parameter

MEDPHARM Company team is committed to providing quality sterilization products, service, parts and

maintenance training at significant savings. From customized parts packages to turnkey equipment

 acquisition and installation, our innovative sterilization solutions are designed to meet our customers' needs.

We understand that untimely breakdowns are costly and can be detrimental to your everyday operations.

Our  service team is compromised of expert technicians that respond quickly to all of your service needs.

We offer on-site service support including inservices, installation and deinstallation of your equipment. From

breakdown  repairs to comprehensive maintenance programs, we have an innovative service solution for you.

We will service on-Site Repairs.Our staff is equipped with the resources required to provide you with

on-site,   on-time repairs in compliance with manufacturer specifications. We also provide installation,

deinstallation, and inservices on most makes and models of sterilization equipment. Near or far we can

 provide you with service support that you need.

Our reconditioning background has taught us of the importance of having quality parts on hand at all times.  We have a large inventory of individual repair parts, as well as preventive maintenance kits, and consumables  in stock and ready to ship today.

With our expert technical support staff, it is not always necessary to have part numbers to place an order.

 We will help you identify the quality parts that you need.