POE-S224F
24 Port IEEE802.3af 10/100Mbps PoE Switch
2 Port Gigabit Copper RJ45 and 2 Port SFP Combo Uplink
8.8Gbps Backplane Bandwidth, 400W Built-in Power Supply
POE-S224F, 24 Port 10/100Mbps unmanaged PoE Switch, 2 Gigabit RJ45 and 2 SFP Slot Uplinks, which 400 Watts internal
power supply. It greatly reduce expense occured by unnecessary equipment for previous
electrical power transmission and labour force for installation by
delivering data and power over a single Ethernet cables (CAT5,
CAT5e, CAT6, etc.) to PoE-enabled devices such as Access Points,
VoIP, IP Cameras and other IP based devices.
Its wide switch capacity of 8.8Gbps is a way to improve office
working efficiency and relieve network congestion. There are LED
lights of indicator designed for showing running status of PoE
Switch on power management and troubleshooting. It also has 400
watts power supply built-in that is going to assign Max. 15.4W for
each PoE Powered Device(PD).
There is always a signature detection and power classification
before a constinuous powering up the PD from POE PSE(Power Sourcing
Equipment) base on its IEEE802.3af standard, which decribes its
typical feature of providing intelligent power solution with energy
saving, safety protection of overload, under-powering and incorrect
installation, etc. PoE-disabled PD can be connected to the switch
and the power will be automatically cut base on PoE PSE auto-sensing technology, which means there is no
validity PoE-enabled PD, so, external PD PoE Splitter is required
to complete the PoE connection with Non-PoE terminal powered
device.
Main Features
1. 24 Port 10/100Mbps unmanaged POE Switch, 2 Port Gigabit RJ45 Uplink, 2 Port SFP Uplink Port
2. Conform to IEEE 802.3f standard
3. Each PoE port output will be up to 25W if less than 12 Port PoE
working simultaneousely
4. Every switch port support auto-negotiation-10/20, 100/200Mbps, 1000Mbps /
2000Mbps (Gigabit).
5. Support MAC address auto-learning and auto-aging
6. Half-duplex/Full-duplex: Prevention of packet loss with back pressure and IEEE 802.3x PAUSE
frame flow control
7. High performance Store and Forward architecture, broadcast storm
control, runt / CRC filtering eliminates erroneous packets to
optimize the network bandwidth
8. Non-blocking switching architecture that forwards and filters
packets at full wire-speed for maximum throughput
9. On/Off power switch; 8.8 Gbps Switching Capacity
Primary Specification
Item: 24 Port Power Over Ethernet Switch (15.4W POE)
Model: POE-S224F
Protocol Standard
- IEEE 802.3 10BASE-T
- IEEE 802.3u 100BASE-TX
- IEEE 802.3ab 1000BASE-T
- IEEE 802.3z 1000BASE-X
- IEEE 802.3x Flow Control
- IEEE 802.3af Power over Ethernet
Power Supply
- Power Consumption: Maximum 390W, Input: 100 - 240 VAC, 50 -60 Hz
- PoE Power Output: 360W
Network Interface
- 24 10/100M ports (MDI/MDIX adaptive) PoE Features
- 2 10/100/1000M Gigabit copper RJ45 ports (MDI/MDIX adaptive)
- 2 SFP GBIC fiber module slots
Primary Performance
- Forwarding modes: Store and Forward
- Bandwidth: 8.8 Gbps (non-blocking)
- Network Latency: (100 to 1000M bps): Max. 20 Microseconds(64Byte)
- Buffer memory: 3Mb per system
- Addressing: 48-bit MAC address
- The Address Database Size: 8,000 per system MAC address
- Mean failure interval (MTBF): 300,000 hours (about 34 years)
Environmental Requirements
- Operating Temperature: 0 °C - 50 °C (32 °F - 104 °F)
- Storing Temperature: -20 °C - 70 °C (-4 °F - 158 °F)
- Operating Humidity: Max.90% Non-condensing
- Storing Humidity: Max.95% Non-condensing
- Working Height: up to 10,000 feet (3,000 meters)
- Storing Altitude: the largest 10,000 feet (3,000 meters)
LED Lights: Indicator of Power Light, Data speed, PoE Power Light
Electromagnetic Radiation:
- CE mark
- FCC Part 15 Class A
- C-Tick
- VCCI Class A
Electromagnetic Immunity: EN 55024
Safety Approval: CE, FCC, RoHS
Dimension: 440mm × 350mm × 44mm; Weight: 5.5 kg
Warranty: One year
Package Content: 24 port POE switch, Power cord, 1U Rackmount Brackets
