POE-S216T
16 Port IEEE802.3at 10/100Mbps 30W POE Switch
2 Gigabit SFP slot Uplink and 2 Gigabit RJ45 Uplink
7.2Gbps Switch Capacity, 400W Internal Power Supply
POE-216T is an 16 port channels unmanaged Power Over Ethernet
Switch that with 16 10/100Mbit RJ45 PoE ports, 2 Gigabit Copper and
2 SFP Combo uplink ports, which is compliance with IEEE802.3af
standard, and it has a 400watts power supply built-in. Power Over Ethernet (POE), as might be expect, describes the use
of a single Ethernet cable(standard gauge cat5, cat5e or cat6,
etc.) to carry electrical power along with Ethernet data. 
There are total 16 output channels PoE, a single port output up to
25.4W, which is suitable for devices such as IP Video Camera,
Wireless Access Point (AP), Access Control, VoIP, etc., they are
also known as Powered Device (PD). So, before the PD is powered up,
there is a procedure for Power Sourcing Equipment (PSE) built in
PoE to implement compatibility checking. The PD must reply a
signature for PSE to check if it's PoE-enabled for the PoE
connection, which take place a few seconds before power is switched
on. It also executes a power classification after first signature
detection process, which will figure out how much the connected PDs
require(Power Class up to approximately 4, 7 and 13 watts), and the
power connection will be automatically cut when the PDs are
disconnected or in incorrect installation, which prevents damages
of overload, underpowring, short-cut or connecting a Non-PoE
device.
Finally, this 16 ways PoE switch will greatly reduces the
comprehensive cost including cables, labour force, time, management
and broken device results from incorrecting installing if no PoE
connection. On the other hand, its 7.2Gbps switching capacity
effectively relieve the office network cngestion and improve
working effeciency.
Main Features
1. 16 Port 10/100Mbps Unmanaged PoE Switch, 2 Gigabit Copper RJ45
Uplink and 2 SFP Slot Combo Uplink
2. Support 16 channles power output delivering to PoE Powered
Device
3. Comply to IEEE 802.3at standard
4. Each Switching port support auto-negotiation-10/20, 100/200Mbps
(Fast Ethernet) and 1000/2000Mbps (Gigabit Ethernet)
5. On/Off power switch, 7.2 Gbps Switching Capacity, Learning and auto-aging
6. Prevention of packet loss with back pressure (Half-duplex) and
IEEE 802.3x PAUSE frame flow control (Full-duplex)
7. High performance Store and Forward architecture, broadcast storm
control, runt/CRC filtering eliminates erroneous packets to
optimize the network bandwidth
8. Non-blocking switching architecture that forwards and filters
packets at full wire-speed for maximum throughput
Detailed Specification
Item: 16 Ports Power Over Ethernet Switch (30W POE)
Model: POE-S216T
PoE Power Output: 48V DC, Max. 30 watts a single port
Power Pin Assignment: 1/2(+), 3/6(-)
Ethernet Port: 16 Ports 10/100Base-TX RJ-45 Auto-MDI/MDI-X
PoE Standard: IEEE 802.3af/at Power over Ethernet / PSE End-Span
Gigabit Port: 2 Gigabit SFP +2 Gigabit RJ45 Uplink
PoE Port: 16 Ports with PoE PSE Injecting Feature
Switch Fabric: 7.2Gbps
Power Supply: 400 watts, Input: 100-240V AC, 50-60 Hz
Flow Control: Back pressure for half duplex, IEEE 802.3x pause frame for full
duplex
Transfer Method: Store-and-Forward
Protocol Standard:
- IEEE 802.3 Ethernet
- IEEE 802.3u Fast Ethernet
- IEEE 802.3ab Gigabit Ethernet
- IEEE 802.3z Gigabit Ethernet
- IEEE 802.3x Full-duplex Flow control
- IEEE 802.3af Power over Ethernet
- IEEE 802.1Q VLAN
- IEEE 802.1p QoS
Ambient Environment:
- Operating Temperature: 0°C ~ 50°C (32°F~122°F)
- Storage Temperature: -40°C ~ 70°C (-40°F~158°F)
- Operating Humidity: 5%~ 90%, Storage: 5%~ 90% (Non-condensing)
Safety Standards: CE, FCC, ROHS
Dimension: 440mm×350mm×45mm (1U height); Weight: 6.2kg
Warranty: One year
