Small Compression Load Cell 100kg Miniature Compression Force
Sensor 1KN
Miniature Compression Type Load Cell FCLB is made of stainless
steel based on strain gauge technology which offers 5kg / 10kg /
20kg / 50kg / 100kg / 200kg / 500kg seven rated capacities to
choose from,compact design makes button type load cell FCLB
suitable for compression force measurement applications with
limited mounting space. Each sensor comes with a 3-meter-long
shielded cable, 4xM2.5 threaded holes located on the bottom make it
easy to mount force sensor FCLB to a flat platform,you may find
Miniature Force Transducer FCLB suitable for applications such as
load distribution analysis, mold pressure measurement, force
overload protection, clamping force measurement, assembly force
monitoring, hydraulics force control and so on. A force sensor is a
transducer that converts force acting on it into electronic signal
which is proportional to the applied force.The acting force causes
deformation of the measuring element,the bonded strain gage deforms
accordingly which will cause the resistance change of the
wheatstone bridge,under constant power supply,the output signal
between Sig+ and Sig- will change proportionally,thus the force can
be measured by measuring the output signal from the load cell.
Miniature Button Load Cell FCLB is designed to measure compression
force,outputs millivolt signal ranging 0~20mV, and signal
amplification may be required for most applications, a load cell
signal conditioner can be used to get 0-5V, 0-10V or 4-20mA signal
proportional to applied force.The amplified output then can be
easily processed by PLCs and data acquisition software.The force
can be displayed through force indicator,force meter FPT is
integrated with high accuracy/low noise 24 bit Sigma-Delta
ADC,sampling speed up to 960Hz makes it suitable for both static
and dynamic measurement;FPT also supports Modbus RTU protocol with
RS485 or RS232 communication port,amplified signal
0-5V,0-10V,0-20mV or 4-20mA is also achievable from FPT.
Dimensions(unit in "mm")
Specifications
| Capacity | 50N / 5kg / 10lb 100N / 10kg / 20lb 200N / 20kg / 45lb 500N / 50kg / 110lb 1kN / 100kg / 220 lbf 2kN / 200kg / 450 lb 5kN / 500kg / 1120 lbf |
| Rated output | 1.5mV/V |
| Excitation | 3-12V |
| Zero balance | ±0.1mV/V |
| Nonlinearity | ±0.5% of the capacity |
| Hysteresis | ±0.5% of the capacity |
| Nonrepeatability | ±0.2% of the capacity |
| Creep(3min) | ±0.1% of the capacity |
| Safe overload | 150% of the capacity |
| Ultimate overload | 200% of the capacity |
| Compensated temperature | -10...+40oC |
| Operating temperature | -20...+60oC |
| Temperature shift zero | ±0.05% R.O./oC |
| Temperature shift span | ±0.05% R.O./oC |
| Input resistance | 1000±100 ohms |
| Output resistance | 1000±100 ohms |
| Insulation resistance | >5000M ohms |
| Ingress protection | IP65 |
| Material of element | Stainless steel |
| Cable | Ø3*3000mm 4-core shielded cable |
| Wiring code | Red--Excitation+ Black--Excitation- Green--Signal+ White--Signal- |
Brief instruction of Rated output(or Sensitivity):
Definition: The signal produced by load cell(or force transducer)
when rated load is applied, expressed in terms of mV/V. The rated
output indicates the output signal range of a sensor.
Sensor output = (Power supply * Rated output) * Load / Capacity
Rated output of Small Button Load Cell FCLB is normally around
1.5mV/V.
Power supply of Small Compression Sensor is normally within 3-12V.
Load / Capacity is within 0-1.
So the output range of Miniature Button Type Load Cell FCLB is
normally within 0...+18mV for compression load measurement.
Example one: Small Compression Load Cell FCLB-100N with 1.5mV/V
sensitivity powered by 10V DC,the output range is 0...+15mV.
Example two: Miniature Compression Force Sensor FCLB-1kN with
1.5mV/V sensitivity powered by 5V DC,the output range is
0...+7.5mV.
Small Compression Load Cell 100kg Miniature Compression Force
Sensor 1KN
Click here to download
datasheet
