Precision Metal Stamping Parts Polished Stainless Steel Motor
Support
Stainless steel support stamping parts are stamped a plate socket
and bended a clip in strip , bended upper section to fix or secure
support stamping part on object and supporting socket with flat
panel is used to support something of motor .
Material
Support stamping parts are made of high tensile strength stainless
steel 18-8 that with good performance or properties .
Tensile strength σb (MPa) | 535 |
Yield Strength σs (MPa) | 210 |
Elongation δ5 (%) | 50 |
Reduction of area ψ (%) | 65 |
Mechanical property of support stamping parts
Fusing point(℃) | 1398 to 1454 |
Specific heat capacity(0~100℃,KJ·kg-1K-1) | 0.5 |
Heat conductivity(W·m-1·K-1) | (100℃)16.3 ,(500℃)21.5 |
Thermal performance of support stamping parts
Resistivity(20℃,10-6Ω·m) | 0.73 |
Electrical performance of support stamping parts
Dimensions
Length : 25 mm
Width : 25 mm
Height : 15 mm
Thickness : 0.8 mm
Chamfer : 0.5 x 45°
Note : we accept customized sizes from 0.5 mm to 5 m for different
designs .
Tolerance
+/-0.1 mm for normal sizes , and refer to following tolerances
standard for unspecified sizes .
| Normal Size | Thickness |
| FM | TO | FM | TO | m |
| 0.5 | 3 | — | 1 | ±0.10 |
| 1 | 3 | ±0.20 |
| 3 | 6 | — | 1 | ±0.15 |
|
| 1 | 4 | ±0.30 |
| 4 | — | ±0.40 |
| 6 | 30 | — | 1 | ±0.20 |
| 1 | 4 | ±0.40 |
| 4 | — | ±0.60 |
| 30 | 120 | — | 1 | ±0.30 |
| 1 | 4 | ±0.55 |
| 4 | — | ±0.80 |
| 120 | 400 | — | 1 | ±0.35 |
| 1 | 4 | ±0.70 |
| 4 | — | ±1.05 |
| 400 | 1000 | — | 1 | ±0.50 |
| 1 | 4 | ±1.00 |
| 4 | — | ±1.45 |
| 1000 | 2000 | — | 1 | ±0.65 |
| 1 | 4 | ±1.30 |
| 4 | — | ±2.00 |
| 2000 | 4000 | — | 1 | ±1.00 |
| 1 | 4 | ±2.00 |
| 4 | — | ±2.60 |
Characteristics
Stainless steel support stamping parts for motor have high tensile
strength and good performance to meet continuous high-load working
.
◆ High tensile strength
Tensile strength is up to 535 σb (MPa) and more higher after heat
treatment .
◆ Perfect elongation
50 δ5 (%) to ensure support stamping parts have enough elongation
under heavy load and pressure . .
◆ Hard material
Support stamping parts are made of stainless steel 18-8 that
hardness is HRC 72 or so .
◆ Resistance to corrosion
Stainless steel 18-8 with good performance on anti-corrosion by
itself . normally , not to be rusted in 5 years inside conditions .
◆ Non-magnet
Its nearly no magnet for stainless steel 18-8 support stamping
parts .
Finish
Polishing for support stamping parts
