Industrial Servo Motor 0.637N.m YASKAWA SERVO MOTOR 100VAC 3000RMP SGMAH-02B1A6C

Industrial Servo Motor 0.637N.m YASKAWA SERVO MOTOR 100VAC 3000RMP SGMAH-02B1A6C

OTHER SUPERIOR PRODUCTS

Do I Run a Hard Servo or a Soft Servo?
High gain servos have come to be known as hard and low gain servos as soft. The higher the gain (A), the
greater the bandwidth (the frequency when A = 1). If one tries to raise the bandwidth too much, the
natural frequencies of the machine come into play and eventually instability occurs causing the machine
to oscillate indefinitely. In addition, as one increases the bandwidth, the servo tries to force the machine
more and more to follow the command. A step input in the command will force the machine to jump.
Over time, a machine could be beat to death by an oversized drive system that is forever jerking it back
and forth in response to commands. The practical approach is to vary the gain and test the machine's
response to a step in command. That response can be viewed on an oscilloscope for number of overshoots
or one can rely on gut feel based on how the machine looks when the step occurs. For heavy industry, 1
IPM/MIL (inches per minute per mil of error) is a typical gain. It is unusual for a piece of industrial
machinery to get above 5 IPM/MIL.

Phases, Poles and Stepping Angles
Usually stepper motors have two phases, but three- and five-phase motors also exist.
A bipolar motor with two phases has one winding/phase and a unipolar motor has one winding, with a center tap per phase. Sometimes the unipolar stepper motor is referred to as a “fourphase motor”, even though it only has two phases.

Motors that have two separate windings per phase also exist—these can be driven in either bipolar or
unipolar mode.

A pole can be defined as one of the regions in a magnetized body where the magnetic flux density is concentrated.

Both the rotor and the stator of a step motor have poles.
Figure 2 contains a simplified picture of a two-phase stepper motor having 2 poles (or 1 pole pairs) for each phase on the stator, and 2 poles (one pole pair) on the rotor. In reality several more poles are added to both the rotor and stator structure in order toincrease the number of steps per revolution of the motor, or in other
words to provide a smaller basic (full step) stepping angle. The permanent magnet stepper motor contains an equal number of rotor and stator pole pairs. Typically the PM motor has 12 pole pairs. The stator has 12 pole pairs per phase. The hybrid type stepper motor has a rotor with teeth. The rotor is split into two parts, separated by a permanant magnet—making half of the teeth south poles and half north poles.The number of pole pairs is equal to the number of teeth on one of the rotor halves. The stator of a hybrid motor also has teeth to build up a higher number of equivalent poles (smaller pole pitch, number of equivalent poles = 360/teeth pitch) compared to the main poles, on which the winding coils are wound. Usually 4 main poles are used for 3.6 hybrids and 8 for 1.8- and 0.9-degree types

It is the relationship between the number of rotor poles and the equivalent stator poles, and the number the
number of phases that determines the full-step angle of a stepper motor. Step angle=360 ÷ (NPh × Ph)=360/N
NPh = Number of equivalent poles per
phase = number of rotor poles
Ph = Number of phases
N = Total number of poles for all phases together If the rotor and stator tooth pitch is unequal, a more-complicated relationship exists

Shenzhen Wisdomlong Technology CO.,LTD Mainly engaged in automation parts, PLCS,DCS,sensors, relays, dirves,encoder, servo drive,soft starter,touch screen,instrument,process control,electric transmission and factory automation aspects of the project design,software programming,technical service and staff training. Our company locats at the central of China,Shenzhen, Guangdong Province. With rapid development, Wisdomlong serves fields of automation in global markets, Our business covers five continents throughout the world with the basic conviction of honest, the international management of customer-centered concept and purpose of bringing convenience to customers. We have confidence to bring our customers more substantial profit with high-quality service and reasonable prices. Choosing us,you will choose a sincere friend and reliable partner. Please feel free to contact us if you are a global manufacturer of high quality brand products who desires to enter the Chinese market or who searches for a Chinese agent.We would like to create a brilliant future with friends in domestic and overseas. All goods sold have one year warranty.

The company with domestic and international numerous well-known brands supplier to build have extremely good relations of cooperation, in Japan, South Korea, southeast Asia, Africa, Europe and the United States, and formed a stable and efficient supply network. The agent and the products are widely used in machinery, equipment manufacturing, electric power, metallurgy, petrochemical, automobile manufacturing industry, paper making, chemical industry, medicine and aerospace industries.

Our Main Brand:

MITSUBISHI

YASKAWA

PANASONIC

GE FANUC

EMERSON

FISHER-ROSEMOUNT

HONEYWEL

ABB

AB

SHNEIDER MODICON

SIEMENS

................