how to mount ultrasonic cleaning transducer for cleaning tank
The principle of arrangement:
1. Cleaning different product layout has different requirements,
such as the degree of oil contamination, the degree of difficulty
in cleaning, the level of cleaning requirements, the design of
cleaning process, all require targeted choices.
2. The arrangement of oscillators is not the more the more dense
the better, the appropriate is the best.
Installation process:
A. Preparatory tools: Argon arc welding, No. 10 inner hexagonal
wrench, chrome-iron-tin wire, 2.5 square high temperature wire,
2*2.5 cable line, oscillator glue, (stripping clamp, casing,
tie-up, sand blasting machine, pipe fittings, etc.);
B. Welding screw: Calculate the arrangement position of oscillator,
weld the screw in the cleared position, then clean the screw
around, make sure it is flat, so as not to affect the installation
of oscillator;
C. Glue configuration: mix glue evenly according to the prescribed
proportion. (Merry, Eroda, 4030 glue mixed before bonding, KMD398
glue mixed in the bonding process);
D. Bonding: Apply the glue evenly on the bottom of the ultrasonic
oscillator, gently twist the air and excess glue between the bottom
of the transducer and the contact surface of the cylinder bottom,
so that the oscillator is more closely integrated with stainless
steel.
E, solidification and condensation: solidification at relatively
high room temperature, 4-8 hours wiring, 24 hours after power test
machine, test machine is absolutely not allowed to exceed empty.
Note:
1. Metal seed nailing machine can also replace argon arc welding.
2. Welding screw must be fully welded, otherwise it will fall off
easily.
3. Regarding curing, temperature should be taken into account for a
long time, low temperature for a long time and high temperature for
a faster time. It is suggested that the curing should be operated
at room temperature, even if it is heated, it should not be
overheated, which is appropriate and best.
4. Where to buy transducer free distribution screw!
Features:
1. Low heat
2. Good thermal stability
3. Frequency and static capacitance consistency strong.
4. Resonance impedance is low.
5. The average length of life.
6. It can be widely used in a variety of ultrasonic cleaning
equipment.
7. High performance: mechanical Q value, high vibration efficiency,
high amplitude
Payment Terms:Prepaid by Bnak, T/T and West Union, ect.
Technical support: All our products adopt advanced technology, produce product with
advanced system, all worker are experienced and skillful.
| Type | Length(mm) | Weight(g) | Frequency(KHz) | Resonance Impedance
(Ω) | Static Capacity
(pF)±10% | Input Power(W) |
ARS-QXHNQ-20100
PZT-8 | 94 | 900 | 20 | 10-20 | 5200 | 100 |
ARS-QXHNQ-25100
PZT-4 | 77 | 710 | 25 | 10-20 | 6600 | 100 |
ARS-QXHNQ-28100
PZT-8 | 66 | 625 | 28 | 10-20 | 5200 | 100 |
ARS-QXHNQ-28100
PZT-4 | 66 | 624 | 28 | 10-20 | 6600 | 100 |
ARS-QXHNQ-30100
PZT-8 | 61 | 555 | 30 | 10-20 | 5200 | 100 |
ARS-QXHNQ-2560
PZT-4 | 77 | 530 | 25 | 10-20 | 5400 | 60 |
ARS-QXHNQ-2860
PZT-8 | 68 | 470 | 28 | 10-20 | 3800 | 60 |
ARS-QXHNQ-2850
PZT-4 | 82 | 425 | 28 | 10-20 | 4100 | 50 |
ARS-QXHNQ-3360
PZT-8 | 58 | 420 | 33 | 10-20 | 3800 | 60 |
ARS-QXHNQ-4060
PZT-8 | 55 | 300 | 40 | 10-20 | 3800 | 60 |
ARS-QXHNQ-4060
PZT-4 | 56 | 310 | 40 | 10-20 | 5400 | 60 |
ARS-QXHNQ-4050
PZT-4 | 54 | 260 | 40 | 10-20 | 4100 | 50 |
ARS-QXHNQ-4050-1
PZT-4 | 57 | 300 | 40 | 10-20 | 4100 | 50 |
ARS-QXHNQ-5435
PZT-4 | 36 | 135 | 54 | 10-20 | 3200 | 35 |
ARS-QXHNQ-6860
PZT-8 | 80 | 460 | 68 | 10-20 | 3800 | 60 |
ARS-QXHNQ-68120
PZT-4 | 67 | 588 | 68 | 10-20 | 7800 | 120 |
ARS-QXHNQ-8060
PZT-4 | 60 | 325 | 80 | 10-20 | 5400 | 60 |
ARS-QXHNQ-12060
PZT-4 | 56 | 260 | 120 | 10-20 | 5400 | 60 |
ARS-QXHNQ-13550
PZT-4 | 54 | 215 | 135 | 10-20 | 4200 | 50 |
Packing:
how to mount ultrasonic cleaning transducer for cleaning tank
