BIFMA X5.1 Furniture Testing Equipment Chair Back Durability Tester

Chair-Back-Durability-Test

Application

This test shall be performed on Type I Tilting chairs with backrests greater than 200 mm in height.

Product introduction
Chair back durability test equipment tests the strength and durability of the seats and backrests by simulating the daily use loading of the seat.
The machine is equipped with two drive devices, which can be individually controlled to repeatedly load the test points of the seat. Through different parameter settings, the machine can do following test on the seat:
1. Seat and back static load test.
2. Seat and back durability test.
3. Seat front edge static load and durability test;
4. Horizontal forward static loading test for backrest.
5. Headrest static load test,
6. Legs forward static load test,
7. Legs lateral static load test.

Technical parameter

a.One pneumatic cylinder with load cell capacity 200N.

b.Adjustable load direction (90° to the chair backrest)

c.Form-fitting load distribution device: A device which distributes a force over a 305 ± 13mm ×70 ± 32mm(12±0.5'' ×2.75'' ± 1.25'') area of a backrest. The device will be shaped to approximate the contours of the chair backrest (refer attachment)

d.2 operation mode:

-Electronic predetermined counter(EPC) - 6 digit counter to stroke the cylinder up to 120.000 cycles.

-Timer - to apply and release the force after 1 minute.

Compressed air: ± 6kg/m²

e.Single phase AC 220V

f.Speed: adjutable (10-30 cycle/minute)

g.Clamp:- to restrain the chair base.

i.Backrest strength test-Static -Type I & II (ANSI/BIFMA X5.1-2017, clause 5)

ii.Backrest strength test-Static -Type III (ANSI/BIFMA X5.1-2017, clause 6)

iii.Backrest durability test - cyclic - Tpye I &II (ANSI/BIFMA X5.1-2017, clause 14)

IV.Backrest durability test - cyclic - Tpye III (ANSI/BIFMA X5.1-2017, clause 15)

Specification

• The max weight is 109kg (240lb)
• The loading device rate between 10 and 30 cycles/minute
• Seating position nearest to the center of the chair
• Determine points 406 mm (16 in.) and 452 mm (17.8 in.) above the seat . Mark these points on the vertical centerline of the backrest.
• Affixed to the test platform. The device shall prevent sliding but not restrict the unit
• from tipping. On chairs that rotate, the base and casters shall be positioned to offer
• the least resistance to rearward tipping of the chair
• Loader: diameter 200mm.

Chair Back Durability Test.pdf

SKYLINE (DONGGUAN SKYLINE INDUSTRIAL CO.,LTD) provides full line of Toys Testing Equipment, Fire Testing Equipment ,Flammability Testing Equipment,Tensile Test Machine, Furniture Testing Machines ,Textile Testing Equipment and other lab test equipment .We also offers value added support services like lab layout, calibration testing procedures / standards, recording techniques and operations of equipment, etc. We have agents to support you in over 10 countries around the world. With a network of representatives providing sales and technical support world-wide.

SKYLINE has achieved good repute in the fields of Fire Testing Equipment, Footwear Testing Equipment, Toy Testing Equipment, Furniture Testing and other lab test equipment.

SKYLINE focus on the lab testing equipment for decads and  we manufacturers the testing instrument as per the international standards like EN71, ASTM, IS 8124 and SRS.

Our major customers are BV, ITS, TUV, SGS, Hasbro and SASO, For these customer 100% testing instruments are supplied by SKYLINE and we are the continuous supplier for these lab. Since SKYLINE is a manufacturer design/develop with advanced technology and having well experienced Technicians which will provide high quality service after sale.

Our main products

Lab Testing Equipment

Flammability Testing Equipment

Fire Testing Equipment

Wire and Cable Fire Tester

Building Material Fire Tester

Toys Testing Equipment

Environmental Test Chamber

Textile Testing Equipment

Furniture Test Machine

Mattress Testing Machine

Temperature And Humidity Test

Our Service

Testing Equipment Design and manufacture

Test Lab Planning and Establish

Toys Test Equipment Upgrade

Toys Test Equipment operation Training

Toys Finish Goods and Mattress  Inspection

Acting for Customer Testing and Certifying

Acting for Foreign Trading Company Quality Inspection

Please have a look at our website and don’ t hesitate to contact us if any items catch your interest. We will do our best to meet your requirement.
Thank you for visiting. We look forward to your inquiry to carry forward win-win cooperation with you soon.