New Hot Product Advertising LED Screen P8 Outdoor Full Color 1/4
Scan Mode HD
Hardware installation
1. Insert the DVI graphics card into the AGP slot of the
motherboard and install the graphics driver.
2. Insert the data acquisition card into the empty PCI slot.
3. Connect the data acquisition card and the graphics card with a
DVI cable.
4. Connect the control line to the serial port (RS232) (optional).
5. Connect to the receiving card with a network cable.
6. Use a 50P flat cable to connect the LED display driver card and
the hub in turn.
7. Check the settings or turn on the debugger power.
Specification of product:
| outdoor P8 LED screen Display |
| Resolution/mm | 8 |
| Pixel configuration | 1R1G1B |
| Pixel density/pixels/m² | 15625/square meter |
| Module resolution | 40*20 |
| Module size/mm | 256*128mm |
| View distance | 14-300m |
| Single point brightness adjust | Can be added |
| Single point color adjust | Can be added |
| White balance brightness | >7500cd/square meter |
| Color temperature | 6500K-9500K |
| Horizontal view angle | 120(degrees) |
| Vertical view angle | 60(degrees) |
| Signal Process bit | 10 or 16bit |
| Grey process | 1024x1024x1024 16834x16834x16834 65536x65536x65536 |
| Control distances | Internet cable:100m, multimembrane:500m, monofilm:2km |
| Driving mode | Constant driving current |
| Scanning mode | static full color SCANNING |
| Fresh rate | 60Hz |
| Refresh frequency | >3000Hz |
| Control mode | Computer synchronous |
| Brightness adjusted range | Manual, automatic operation, stepless continuous adjusted |
| 255 steps. No grey loss |
| Out of control point | <1/10000 |
| Working hours | ≥72hours |
| Mean Time Between Failure | >5000hours |
| Life time | 100000hours |
| Life-all-white(brightness halving) | 50000hours |
| Environment temperature range | Operating temperature range: -20-45℃ |
| Self-check technology | LED spot self-check, communications check, power check, |
| temperature monitor(need customization) |
| Remote monitoring | Remote supervision and control, record potential fault, |
| send out warning signs to the operators.(need customization) |
| Software environment | WindowsNT,Windows1999,WindowsXP |
| Luminous point width between centres | Deviation<3% |
| Brightness uniformity | <10% |
| Waterproof | IP65 |
| Color uniformity(chromaticity coordinate) | ±0.003 |
| Power supply request | AC85-264V(50Hz-60Hz) |
| Contrast | (1000:1) |
| System protection | Moistureproof,dustproof,high temperature
protection,anti-corrosion,anti-burning,anti-static,anti-vibration |
| Humidity(working) | working:10-95% |
| Humidity(storing) | storing:10-95% |
Packing and shipping:
In our company,usually use the wooden and flight cases for
package,wooden for Iron cabinet,and the flight for Die casting
cabinet.In this way can help you to save the transportation
expenses.For shipping,we have sea and air,in which way just all up
to you.Also,if you want other way,we can accept.
Two types of modules:
A. DIP package
DIP package, which is the abbreviation of dual inline-pin package,
commonly known as plug-in type. It was the first to develop. The
LED lamp bead is produced by the manufacturer, and then inserted
into the LED lamp board of the LED by the LED module and the LED
display manufacturer, and the DIP semi-outdoor module and the
outdoor waterproof module are produced through wave soldering.
However, due to the influence of the diameter of the lamp bead,
only P6 can be achieved at present. Other P5, P4 and even higher
density outdoor LED displays cannot be made. However, the
protection performance of the direct insertion is good, but the
viewing angle is not accurate and fixed, generally between 100-110,
and the energy consumption is high, and it is not environmentally
friendly, so it is only suitable for outdoor small-pitch LED
display, and currently in the outdoor P10-P20 Have a large market
share.
Moreover, it is produced by DIP packaging, the process is
complicated, it is not easy to mechanize production, and the
production efficiency is low. In addition, there are many DIP
manufacturers, there is no high technical and equipment threshold,
and the competition is fierce. Many manufacturers use inferior raw
materials and PCB boards to reduce the cost to gain market share,
low quality, and almost no perfect after-sales guarantee.
B. SMD package
SMD packaging, which means: surface mount device, is a type of SMT
component. Surface mount components came out about twenty years
ago, opening up a new era. For a long time, people have believed
that all pin components will eventually adopt SMD packaging. SMD
technology is widely used in LED outdoor displays.
The three-in-one label we often talk about is actually a kind of
SMD technology, which refers to the SMT lamp beads packaged with
three different color LED chips of RGB encapsulated in the same
colloid at a certain interval.
The advantages of the standard three-in-one outdoor full-color LED
display are: the full-screen viewing angle is large, the surface
can be treated with light diffuse reflection, the obtained effect
is free of graininess, the color saturation is high, and the color
uniformity is good. The overall flatness of the three-in-one is
easier to control, and it has always been the standard technology
for high-definition outdoor LED displays.
In recent years, with the continuous improvement of technology
development and production processes, SMD has developed rapidly and
the cost has been continuously reduced. It has now become the
mainstream product of LED indoor displays. In addition, SMD has
also developed rapidly in the outdoor market, but brightness and
waterproof and moisture-proof have always been difficult problems
to overcome. I believe that with the continuous development of the
entire industry, the development of outdoor LED displays is an
inevitable trend.
FAQ
1.Q:Are you a factory or trading company?
A:We are a factory,located in Dalang,Longhua District .
2.Q:What kind of payment terms you accept?
A:We accept T/T,Western Union,MoneyGram etc.
3.Q:What's packaging?
A:1.Flight case packaging
2.Wooden case packaging
3.36pcs in one case packaging
4.Customized packaging
4.Q:Does you have CE/ROHS certificates?
A:Yes, we offer the CE & ROHS certificates .
5.Q:What's the shipping method,shipping time?
A:Our products could be shipped by Sea, by Air, and by Express.
by sea:20-40days; by air:5-10days ;by express:3-6days
Welcome to Shenzhen ShiChuangXin Ke Electronic Co.,Ltd.We are
wating for you all the time online!!!
