CN089 SMT Wave Soldering Machine Lead Free 670KG Weight With PID Control

CNSMT 10 years production WAVE SOLDERING MACHINE after dip component

Feature

Application

Wave soldering machine basic operating procedures

(Reference)

B1 wave soldering machine basic operating procedures

B1.1 Preparation

a. Check whether the wave soldering machine is equipped with ventilation equipment is good;

b. Check the wave soldering machine timing switch is good;

c. Check if the tin bath temperature indicator is normal.

Method: Adjust the temperature indicator up and down, and then use a thermometer to measure the temperature of the tin bath surface 10-15 mm, and determine whether the temperature changes with it:

d. Check whether the preheater system is normal.

Method: Turn on the pre-heater switch and check if it is warm and the temperature is normal.

e. Check the operation of the cutting knife.

Method: Adjust the height of the blade according to the thickness of the printed circuit board and the length of the remaining component lead. Then tighten and stabilize the blade holder, start the visual inspection of the rotation of the blade, and finally check the failure of the insurance device;

f. Check whether the supply of compressed air to the flux container is normal;

Method: Pour the flux, adjust the inlet valve, start the flux foam, use the sample board to adjust the foam to 1/2 of the plate thickness, and then tighten the IOP valve until the formal operation. Then move this valve, just open the air intake switch;

Operating rules

a. The wave soldering machine must send 1 to 2 trained professional staff for operation and management, and be able to perform general maintenance;

b. Before starting the machine, the operator must wear roving gloves and wipe the equipment clean with cotton yarn, and inject proper amount of lubricant into the oil injection hole;

c. Operators should wear rubber anti-corrosion gloves to remove waste and dirt around tin tanks and flux tanks;

d, no flammable articles such as gasoline, alcohol, cotton yarn, etc. shall be stored around the equipment in the operating room;

e. When the welder is running, the operator must wear a respirator and wear a heat-resistant flame-resistant glove.

f. Non-workers shall not enter the wave soldering operation room casually;

g. smoking in the workplace is not allowed to eat food;

h. Wear work caps, shoes, and work clothes when performing the insertion work.

B2 single machine wave soldering operation

B2.1 Open the ventilation switch.

B2.2 boot

a. Turn on the power;

b. Switch on the solder bath heater;

c. Open the foam switch air intake switch;

d. When the solder temperature reaches the specified data, check the tin level. If the tin level is too low, add solder in time;

e. Turn on the wave solder gas pump switch and adjust the tinning depth with a special fixture equipped with a printed board;

f. Remove residual oxide from the tin surface and add anti-oxidant after the tin surface is clean:

g. Check the flux, if the liquid level is too low, add appropriate amount of flux;

h. Check to adjust the flux density to meet the requirements;

i. Check whether the flux foam layer is good;

j. Turn on the preheater temperature switch and adjust to the desired temperature position; k. Adjust the angle of the drive rail;

l. Turn on the conveyor switch and adjust the speed to the required value;

m. Open the cooling fan;

n. The welding fixture into the guide;

o. The printed board is loaded into the fixture, the board is tightly clamped around the fixture slot, the force is moderate, and then the fixture is placed at the beginning of the transfer rail;

p. Prior to the welding operation, the tilted components shall be straightened by a person, and the correct components shall be verified;

CNSMT  was established in June 2005

with a registered capital of 6 million yuan and more than 60 employees.

The company's core personnel of the professional R&D team have 15 years of automated R&D and manufacturing experience.
CNSMT mainly develops and sells SMT pick and place machines, printing presses, reflow welding, wave solder machine, loader and unloader, conveyor, AOI, SPI, and peripheral auxiliary equipment.

The company has developed and mass-produced refow oven and wave welding machine at the end of 2010. The machine is the first in the country.

The sales volume of products reached more than 200 units in half a year.
Our philosophy: integrity, strength first, wholeheartedly for the customer.

Our company adhering to the customer first, service-oriented business philosophy,

benign competition, will continue to work hard to learn, so that more customers to use the quality and cheap SMT china high-end equipment, for customers to save labor costs, factory costs.