High Power Stationary RCIED Bomb Jammer, High Power DDS Jammer,
Full Band Wireless Signal Jammer
User Manual - > Remote Controlled Improvised Explosive Device Jamm...
Product Instruchtion
Now let us introduce this mobile signal jammer to you and give you
better understanding of the positions of all the buttons, functions
of accessories and other hardware.
Control Panel
Tag:Front Panel View
Tag: Back Panel View
Tag: RF POWER SWITCH
Press the green light button to activate corresponding power
amplifier
Tag: Warning LED
Red Light With VSWR Warning
Tag: Each is 31dB adjustable output power adjustable step is 1dB
Product Technique characteristics
- Taking use of super-high frequency with high effective power.
- Effective output power (channel power) and bigger interfere radius.
- Only interfere downlink frequency of mobile system,without disturb
normally working of Base Stations.
- Imported elements: Slow start up design of circuit. These elements
can maintain the stable operation condition with high integration.
A combination of the Israeli and United states of American
Technology. Most sensitive Components imported from Germany,
Hungary and Japan.
Product Parameter specifications
| Channel | Center Frequency | Frequency Range | Band Width | Output Power | Channel Output Power |
| CH1 | 54MHz | 20-88MHz | 68MHz | 50dBm | 19dBm/30KHz(min) |
| CH2 | 1842.5MHz | 1805-1880MHz | 75MHz | 51.3dBm | 18dBm/30KHz(min) |
| CH3 | 121.5MHz | 88-155MHz | 67MHz | 50dBm | 19dBm/30KHz(min) |
| CH4 | 1960MHz | 1930-1990MHz | 60MHz | 51.3dBm | 19dBm/30KHz(min) |
| CH5 | 375MHz | 300-450MHz | 150MHz | 50dBm | 20dBm/30KHz(min) |
| CH6 | 2441.75MHz | 2400-2483.5MHz | 83.5MHz | 50dBm | 18dBm/30KHz(min) |
| CH7 | 872.5MHz | 851-894MHz | 43MHz | 51.3dBm | 20dBm/30KHz(min) |
| CH8 | 942.5MHz | 925-960MHz | 35MHz | 51.3dBm | 22dBm/30KHz(min) |
| CH9 | 1575.42MHz | 1570.42-1580.42MHz | 5MHz | 50dBm | 18dBm/30KHz(min) |
| CH10 | 2135MHz | 2100-2170MHz | 60MHz | 51.3dBm | 20dBm/30KHz(min) |
| Power Supply:AC 220V Shielding area:100-500M @ according to signal
density mobile |
| Power consumption:3000 W Weight:64.5 Kg Side(length×wide×high):
640x400x400 mm |
System fittings
System fittings consist of block package, panel antenna, antenna
connecter lines (cable and N connecters) etc. 10 modules are
responsible respectively for CDMA, GSM, DCS,WiFi,WLAN, which
controls adjustment of output power, power switcher, as well as
kinds of alarms( over heating and VSWR) . The next step will
provide the function of each fitting in brief.
Anntenna
The jammer you bought is made up of jammer and antennas. It
contains 10 modules(CH1~CH10).Each module can adjust power, warning
standing wave indicator and warning temperature indicator
separately.
Frequency: 20~88MHz,88~155MHz,300~450MHz ( total 3pcs ).
Gain : 3dbi.
Connector type : N type
Photo:
Vertical Ichnography:
| Frequency Range | 20~88MHz | 88~155MHz | 300~450MHz |
| Model | TQJ-100-3 | TQJ-150-3 | TQJ-300/400-3 |
| Input Impedance | 50Ω |
| VSWR | ≤1.8 |
| Gain | 3dBi |
| Maximum Power | 150W |
| Polarization | Vertical Polarization |
| PIM | <-107dBm |
| Connector Type | 7/16 or N-K |
| Lighting Protection | Direct Ground |
| Wind Velocity | 60(m/s) |
| Hold Pole Diameter | φ40(mm) |
- Directional Board antenna
Frequency:925~960MHz/1805~1880MHz,851~894/2110-2170MHz,1570.42~1580.42/2400~2483.5MHz,1930~1990MHz
( total 7pcs )
Gain:12-15dbi
Interface: N type
Photo:
Vertical Ichnography:
| Frequency Range | 851~894 MHz | 925~960 MHz | 1570.42~1580.42 MHz | 1805~1880 MHz | 1930~1990 MHz | 2110~2170 MHz | 2400~2483.5 MHz |
| Model | ANT-800-2500-12 |
| Input Impedance | 50Ω |
| VSWR | ≤1.8 |
| Gain | 12dBi |
| Maximum Power | 150W |
| Polarization | Vertical Polarization |
| PIM | <-107dBm |
| Connector Type | 7/16 or N-K |
| Lighting Protection | Direct Ground |
| Wind Velocity | 60(m/s) |
| Hold Pole Diameter | φ40(mm) |
Using Guide
Step 1: opens the box
- Open the box. Keep unpacked boxes ready for future removal or
shipment.
- Check that the open equipment and accessories are in good
condition. If you find any existing defects or damage, please
contact your supplier as soon as possible.
Step 2: connecting cables and antennas
- Coaxial cables are mainly used for the connection of antennas and
shields.
- (Note: do not activate the shield until the antenna and shield are
not well connected, otherwise, the shield will be severely damaged.
All costs and consequences arising therefrom will be borne by the
user himself)
- Cable the antenna to the mainframe port one-to-one.
- Insert the cylindrical end of the 3 pin AC input power cord into
the "AC220V" AC power outlet of the host, and insert the 3 pin head
end into the power supply socket.
Step 3: Start shield
- Press the RF switch and the amplifier starts working while the
orange light in the RF switch is lit.
- The minimum output power of the shield can be adjusted by the dial
disk of the front panel (control panel) of the host machine
according to the actual situation in the field.
Step4: Turn off the shield
- Press the RF switch that has already lit the orange lamp, the
orange light goes out, the power amplifier stops working.
- Disconnect "AC 220V" AC Power Line from Power supply.
- Remove antenna connection cable.
