Q40 GFUVE Alternating Current Clamp On Current Transformer Ratio
500A / 5V 2.5 Meter Cable
The GFUVE Q40-2 Split Core Current Sensor has high frequency
available for oscilloscope, excellent linearity performance. The
distinct jaw shapes to be used for hooking or prying around the
conductor.
In electrical and electronic engineering, a current clamp or
current probe is an electrical device with jaws which open to allow
clamping around an electrical conductor. This allows measurement of
the current in a conductor without the need to make physical
contact with it, or to disconnect it for insertion through the
probe. Current clamps are typically used to read the magnitude of
alternating current and, with additional instrumentation, the phase
and waveform can also be measured. Some clamp meters can measure
currents of 1000 A and more. Hall effect and vane type clamps can
also measure direct current.
GF438II PQA with Three 500A Clamp-On Current Transformers, 40mm
Model: Q40 This Power power quality analyzer set comes with 4pcs
Q40 clamp-on current transformers that have a 10mA to 500Arms
measuring range and a 40mm diameter maximum conductor size.
The GFUVE clamp-on current transformer is very popular with our
customers due to its fast and easy installation Produced with
amorphous silicon core or permalloy core, this product features
small size, high precision good stability and good
anti-interference This product is widely used for measuring power
and energy in the fields of electric power, communication and
monitoring system. Besides the high precision and the small phase
error this clamp-on current transformer can be used to measure a
wide variety of electric parameters without disconnecting the
exiting electric system.
Features
Measurement range of 1mA to 600A AC
Large jaw opening designed
Improved ergonomic design and easy operation
High content nickel metal core
Conforms to EN 61010, 600V CAT III
Low phase shift for power measurement
Designed for DMMs, recorders, loggers, oscilloscopes, power and
harmonic meters
UL, CE mark
Applications
Power quality measuring
Large industrial loads
Measuring around cable bundles
Power load monitoring
Waveform analysis
Energy meter calibrator
Parameter
| Electrical parameters |
| Ratio | 1000: 1 or 2000:1 (customized) |
| Accuracy class | 0.1%, 0.2%, 0.5% |
| Primary current | 0 - 500A AC |
| Secondary current | 0 - 1A AC or 0-5V AC (customized) |
| Max. Cont. Input current | 600A |
| Over voltage category | CAT III 600V |
| Output signal (AC current) | 250mA,500mA,1A,5A AC at nominal input current |
| Output signal (AC voltage) | 250mV, 500mV, 1V, 5V AC at nominal input current |
| Frequency range | 40Hz-2000Hz |
| Dielectric strength | 3KV 50Hz/60Hz at 1 minute |
| Temperature range | -20°C to +55°C |
| Output | 2.5 meter cable with D01 connector |
| Max. voltage not insulated conductors | 600 V |
| Standard | EN 61010-1, EN 61010-2-032, IEC60044-1 |
| Installation | Clamp type |
| Output mode | Lead output (2.5m) |
| Mechanical parameters |
| Dimensions (L x W x H) (mm) | 82 x 290 x 25.3 |
| Weight (g) | 500 |
| Holding wire diameter (mm) | φ40 |
| Max. jaw opening (mm) | 40 |
| Color | Black |
| Material | PC+ABS+Polycarbonate, UL94 V0 |
Photos
FAQ, following questions will help you to select the matched probe
for your applications.
1. Please determine if you are measuring AC or DC?
GFUVE Q40-2 is for AC measuring.
2. What is the maximum current you will measure?
Q40-2 max current is 600A
3. What size conductor will you clamp onto? This parameter
determines the probe jaw size needed.
Q40-2 can clamp conductor within φ40mm
4. What type of probe output do you need or can you work with (mA,
mV, A, AC, etc.)?
Q40-2 can customize output with Amp, Volt.
5. What is the working voltage of the conductor to be measured?
GFUVE probes should be used below 600 volts
6. What type of termination do you need: jacks, leads or BNC?
Q40-2 standard has 2.5meter leads. We can offer jacks or BNC… as
options.
7. If you cannot find information you need or would like
assistance, contact us today. We have designed many more probes
than those shown in this catalog, and we manufacture in Beijing,
China.
