Soundproofing Work Insulation Stick Pins with Washer for Glass
wooland rock wool
The Insulation Stick Pins with Washer is a insulation hanger, it is fabricated by a 2" X 2" metal base
with a tape on the back riveted
with a pin, we also call it as self-adhesive pin or peel&press
pin, it works with a self locking washer to fasten the insulation,
different
from the perforated base pins, they are used for sticking onto new
or clean sheet metal of insulation construction.
Detail Specification Of Insulation Stick Pins with Washer
Material:Low carbon steel, Aluminum or stainless steel.
Plating pin: galvanized coating or cooper plated
Plating base: galvanized coating,
Self-locking washer: Available in all kinds of sizes, shapes and
materials
Base size 2"×2"
Pin size :12GA( 2.7mm)
Pins length:1" 1-5/8" 1-1/2" 3-1/2" 4-1/2" 5-1/2" 6-1/2" etc
Accept customization for other lengths
HUIHAO Insulation Stick Pins with Washer
| Pin diameter | Base size | Pin length in common | Washer |
| 12 Ga (2.7mm or 0.106'') | 2''x2''base (50mmx50mm) | 1'' | Available |
| 12 Ga (2.7mm or 0.106'') | 2''x2''base (50mmx50mm) | 1 1 / 2'' | Available |
| 12 Ga (2.7mm or 0.106'') | 2''x2''base (50mmx50mm) | 1 5 / 8'' | Available |
| 12 Ga (2.7mm or 0.106'') | 2''x2''base (50mmx50mm) | 3 1 / 2 ‘’ | Available |
| 12 Ga (2.7mm or 0.106'') | 2''x2''base (50mmx50mm) | 4 1 / 2 ‘’ | Available |
12 Ga (2.7mm or 0.106'') | 2''x2''base (50mmx50mm) | 5 1 / 2 ‘’ | Available |
| 12 Ga (2.7mm or 0.106'') | 2''x2''base (50mmx50mm) | 6 1 / 2 ‘’ | Available |
The most popular type is 2.7mmx65mm and 3.0mm x130mm.
The length of the Self Adhesive Insulation Pins also could be
customized .
Advantages of the Insulation Stick Pins with Washer
1. Environmentally-friendly
2. Light, dust free, fire retardant and easy to install
3. Heat reflection, heat insulation, sound insulation, counter
radiation, counter vibration and shielding
4. During Summer: moisture barrier, sun protection, waterproof,
energy saving consumed by cool air conditioning
5. During Winter: heat protection, remarkable energy saving
consumed by warm air conditioning
The pins could have washers together
Application of insulation stick pins
Best results are obtained when ambient temperature is above 40° F
at the time of application. Remove the release paper from the base
plate and apply hanger to a suitable flat surface. A firm straight,
forward pressure should be used. Do not twist. Due to the
quick-tack nature
of the adhesive, it is very important that the release paper not be
removed until ready to apply the hanger. Insulation may be applied
immediately after properly securing the hanger. Hangers should be
stored at 75° F and 50% relative humidity. It is important that
stock be
rotated. Shelf life is estimated at 2 years if stored as
recommended
WIPE SURFACE CLEAN.Anchor should be applied to a clean, dry
non-porous surface
PEEL OFF RELEASE BACKING.NOTE: Double faced foam tape has a
one-year active shelf life
STICK ANCHOR IN PLACE.Select location before contact with
surface.Press firmly
APPLY FIRM PRESSURE.20 pounds of pressure should be applied all
around the base of the anchor
ALLOW TO STAND 15-20 MINUTES.This will permit better adhesion to
take place
