High Brightness smd 3535 Outdoor P6 LED Display for Advertisement
What is difference between SMD and DIP led display?
Surface Mounted Device LED is short for SMD,through the SMT
technology encapsulating diode, soldering this lamp on the PCB
board surface. Widely used for indoor projects.
Dual in-line Package is short for DIP, after soldering the LED
lamp's feet to stable it on the PCB., so it names of DIP LED.
Mainly used for outdoor projects.
The comparison of SMD and DIP. SMD with RGB 3 colors in 1 LED cup
technology, with better colors uniformity, and wider viewing angle,
usually, SMD can be done the small pitch pixels,
so for some high resolution LED screen, SMD is the best choice.
DIP technology with LED foot in PCB board, then the heat
dissipation is better than SMD, and higher brightness, even under
the sunshine, DIP LED screen can also show the contents well.
That is the reason why people like DIP for outdoor used.
For the energy saving influence, SMD is a new technology, it is
high luminous efficiency and good heat dissipation,SMD is 30%
energy saving more than DIP.
Previously,SMD is only used for indoor LED screen, but with
technological breakthroughs in recent years, SMD brightness has
been greatly improved,
waterproof processing also be completely resolved, therefore, SMD
is more and more applied to the outdoor LED display in market.
Specifications :
| outdoor SMD P6 |
| Resolution/mm | 6 |
| Pixel configuration | 1R1G1B |
| Pixel density/pixels/m² | 43222/m² |
| Module resolution | 27778 |
| Module size/mm | 192x192mm |
| View distance | 14-300m |
| Single point brightness adjust | Can be added |
| Single point color adjust | Can be added |
| White balance brightness | >7500cd/㎡ |
| Color temperature | 6500K-9500K |
| Horizontal view angle | 120(degrees) |
| Vertical view angle | 60(degrees) |
| Signal Process bit | 10 or 16bit |
| Grey process | 1024x1024x1024 16834x16834x16834 65536x65536x65536 |
| Control distances | Internet cable:100m, multimembrane:500m, monofilm:2km |
| Driving mode | Constant driving current |
| Scanning mode | 1/13 SCANNING |
| Frame rate | 60Hz |
| Refresh frequency | >3000Hz |
| Control mode | Computer synchronous |
| Brightness adjusted range | Manual, automatic operation, stepless continuous adjusted |
| 255 steps. No grey loss |
| Out of control point | <1/10000 |
| Working hours | ≥72hours |
| Mean Time Between Failure | >5000hours |
| Life time | 100000hours |
| Life-all-white(brightness halving) | 50000hours |
| Environment temperature range | Operating temperature range: -20-45℃ |
| Self-check technology | LED spot self-check, communications check, power check, |
| temperature monitor(need customization) |
| Remote monitoring | Remote supervision and control, record potential fault, |
| send out warning signs to the operators.(need customization) |
| Software environment | WindowsNT,Windows1999,WindowsXP |
| Luminous point width between centres | Deviation<3% |
| Brightness uniformity | <10% |
| Color uniformity(chromaticity coordinate) | ±0.003 |
| Power supply request | AC85-264V(50Hz-60Hz) |
| Contrast | (1000:1) |
| System protection | Moistureproof,dustproof,high temperature
protection,anti-corrosion,anti-burning,anti-static,anti-vibration |
| Humidity(working) | working:10-95% |
| Humidity(storing) | storing:10-95% |
Technical service:(
(1) Provide system and product training prior to construction in
order to fully understand the product;
(2) Provide installation training to enable installation and
maintenance of the system;
(3) Application training provided at the end of the project to
enable users to become proficient in the use of the system
hardware;
(4) Free training for new employees when users change;
(5) We are responsible for training your staff in the use of the
system;
Spare Parts Warranty Configuration Guidelines
(1) Adequacy: Match with specific equipment, spare parts
configuration is sufficient to ensure that the first time to
replace the equipment in the event of failure;
(2) Necessity: on the basis of previous maintenance experience, we
configure spare parts are the key parts of the equipment, so as to
ensure the economy of the configuration;
(3) Economical and practical: In order to deal with faults in the
shortest possible time, we configure spare parts are complete
modules or units, and through our training, the owners can easily
replace the spare parts so as to ensure the normal operation of the
system.
♦ Why choose us
Continues Quality
With more than 10 years experience in led display
producing,equipments are updated regularly.What’s
more,unique standardized and module production ensure our products
continuous quality.
Competitive Price
With large scale production capacity and professional production
technology,our company have built
effective modular production.We always stick to promote the
technical innovation and reduce cost to
benefit customers.
Fast Delivery
Once we promise the delivery date,we will try our best to fulfill
it.Special procedures such as emergency
inventory will be used to maintain your uninterrupted supply of the
products.
Perfect Service
Pre-sales:Your purchasing requirements will be highly valued and
we’ll recommend suitable products to
you.
After-sales:We will track the products usage and then constantly
perfect our products.
♦ Frequently Asked Questions
What kind of payment terms you can accept ?
We can accept T/T and Western Union.
What about your Led Display quality ?
Checking in the whole manufacturing process&100% inspection
before shipment ensure the quality of
our products continuity.
What is your delivery time ?
Within 7-35 days according to your area and quantity.
Is your LED display competitive ?
Yes,we are led display manufacturer for more than 10 years.Mass and
professional production ensure
our led display’s competitiveness.
Welcome to visit our website and inquire us more info,waiting for
you all the time!!!
