SFC-IEC-A1B series 5 to 14" 15Amp Hardwired Power Strip with 2 Outlets
This hard wired type power strip is good for installation in your
kitchen, cabinet, on the rack and so on. It is not for normal wall
outlets. There is no power cord and plug with this unit.
Features
- 5" to 14” - Durable Aluminium alloy Metal Housing Power Strip
- 2 Black ( white or grey or other) US NEMA 5-15R Outlets, Vertical or
level Outlet Orientation
- Hardwired without Power Cord for Mounting at Your Desired Location
- One IEC C 14 Input on Each Side - (on the Top or Bottom Cover or Both Sides or Ends)
- Electrical Ratings: 100-125V 60Hz 15A
- UL C-UL Approved and Listed
- Outlets 0.12" to 8.39" (3mm to 213mm) apart center to center
- With IEC C13 Cable Easier put in C14 inlet and Faster Installation
- Higher Efficiency
| |
| Model #: | SFC-IEC-513 |
| Description: | 5 to 14" 2 Outlet Hardwired Power Strip |
| Power Strip Measurement: | L5 to14" x W1.614" x H1.255" (133 to 355 x 45 x 42) * |
| Outlets: | 5 |
| Outlet Color: | Black, white, grey or other |
| Outlet Orientation: | Vertical or level |
| Receptacle Type: | NEMA 5-15R |
| Outlet Spacing: | 0.12to 8.39" (3 to 213mm) (center to center) |
| IEC C14 Inlet: | on Top or Bottom Cover or Both Sides or Ends) |
| Voltage Input/Output: | 110-125V 60Hz |
| Current Input: | 15A |
| Full Load: | 1875VA |
| On/Off Switch: | Yes |
| Circuit Breaker: | 15A |
| Surge Protection: | N/A |
| Indicators: | Yes |
| Mounting Tabs: | On both ends or bottom |
| Mounting Clips: | Mounting Clips included |
SAFETY WARNING:
Installation work of this unit must be done by a professional, a
licensed electrician or an electric engineer.
Never install this unit during a thunder storm.
Switch off the power before you start installation work.
This unit is for indoor use only.
This unit is not intended for use in or around wet or potentially
wet areas including, but not limited to, aquariums, saunas, showers
and fountains.
Risk of Electric Shock!
INSTALLATION GUIDE:
Before installation, you may need to get a IEC C13 Outlet. Decide
your wire gauge, and ask store attendant for assistance what color
of connectors you should get) from your local hardware or electric
supply or home improvement stores.
Minimum tools required: A fine to medium fine philips screw driver,
and a pair of scissors, and a pair of mid size slip joint pliers
1. Turn off electricity in the house
2. Decide where to place this unit
3. Choose the side you want the cord exit to choose IEC C14 Built
in power strips
4. Match the color of the wires and secure the wire connection with
proper wire connectors built in IEC C13 plug.(different wire gauge use different colored wire connectors)
- Mount the power strip where you want it to be:
A) For power strips with mounting tabs on both ends: screw down the
unit on the floor, wall or in your cabinet or on your rack, where
you want it to be
B) For power strips without mounting tabs, but to be mounted with
clips, place the unit where you want it to be first, make marks
where to install the clips, which normally should be placed about
min 2”<power strips length away from each end, and then screw
the clips down with screws provided. Then, snap the power strip in
on the clips - Push IEC C13 outlet plug into IEC C13 inlet power strips , and push
switch to ON. Turn electricity back on, you are ready to go.
Note:
We also custom manufacture for our customers.
