Allen Bradley 1442-PS-2505M0510A 1442PS2505M0510A AB 1442 PS 2505M0510A

Allen Bradley 1442-PS-2505M0510A 1442PS2505M0510A AB 1442 PS 2505M0510A

Product Description:

The ground conductor of the motor cable should be connected to the drive ground (GRD) terminal directly. Connecting this ground conductor to a cabinet ground point or ground bus bar may cause high frequency current to circulate in the ground system of the enclosure. The motor end of this ground

conductor must be solidly connected to the motor case ground. Shielded or armored cable may be used to guard against radiated emissions from the motor cable. The shield or armor should be connected to the drive ground terminal and the motor ground as outlined in the Grounding section of this Installation

chapter. Common mode chokes are recommended at the drive output to reduce the common mode noise. An RFI filter can be used and in most situations provides an effective reduction of RFI emissions that may be conducted into the main supplylines. If the installation combines a drive with sensitive

devices or circuits,it is recommended that the lowest possible drive PWM frequency be programmed.

Contact Information:

Contact:Miya ( manager)

Email :sales@mooreplc.com
Q Q: 2851195450
Skype: miyazheng520
Mobile:86-18020776792 ( what's app )

Related Product Recommendation:

For the requested packet interval, enter the number of milliseconds desired between each I/O message
between the ControlLogix processor and the 1203-CN1. The 1203-CN1 can handle a packet interval as
low as 5 milliseconds; therefore, make sure that this value is set to at least Click the "Finish" button to

complete the configuration of the I/O connection in RSLogix 5000. At this point, download your configuration to the ControlLogix processor, then exit RSLogix 5000. To actually schedule the I/O, you will need to start RSNetWorx for ControlNet. Once RSNetWorx starts, go online to the ControlNet network

containing the ControlLogix chassis and 1203-CN1 being configured. Turn on the "Enable Edits" check box, then save the network. This causes the I/O connection created in RSLogix 5000 to be scheduled in the ControlLogix processor. After a few seconds, the I/O LED on the ControlLogix processor and the

module LED on the 1203-CN1 should stop blinking and remain green. If they do not, it could indicate a number of I/O-related problems

1745-E101 Expansion Unit AB
1745-E102 Expansion Unit AB
1745-E103 Expansion Unit AB
1745-E104 Expansion Unit AB
1745-E105 Expansion Unit AB
1745-E106 Expansion Unit AB
1745-E107 Expansion Unit AB
1745-E151 SLC 150 Expansion Unit AB
1745-E152 SLC 150 Expansion Unit AB
1745-E153 SLC 150 Expansion Unit AB
1745-E154 SLC 150 Expansion Unit AB
C SLC 150 High Speed Input Module AB
1745-E156 SLC 150 Expansion Unit AB
1745-E157 SLC 150 Expansion Unit AB
1745-LP101 Processor Unit AB
1745-LP102 Processor Unit AB
1745-LP103 Processor Unit AB
1745-LP104 Processor Unit AB
1745-LP151 SLC 150 Processor Unit AB
1745-LP152 SLC 150 Processor Unit AB
1745-LP153 SLC 150 Processor Unit AB
1745-LP154 SLC150 SLC 150 Processor Unit AB
1745-LP156 SLC 150 Processor Unit AB
1745-LP157 SLC 150 Processor Unit AB
1745-M1-- EEPROM Memory Module AB
1745-PCC SLC Personal Computer Interface Converter AB

1745-PT1 Hand Held Programmer AB
1745-TCAT TCAT SLC-100 Timer Counter Access Terminal AB
1746-A10 10-Slot Chassis AB
1746-A13 13-Slot Chassis AB
1746-A2 2-Slot Expansion Rack AB
1746-A4 4-Slot Chassis AB
1746-A7 7-Slot Chassis AB

APPLIED MATERIALS P/N 1220-0025 BAR IONIZER 7-EMITTERS 28.4"LONG 28VAC ADAPTER

APPLIED MATERIALS P/N 1350-01200 BARATRON PRESSURE TRANSMITTER

APPLIED MATERIALS P/N 3700-01245 O-RING id .364 CSD .070 VITON 75 DURO BLK

APPLIED MATERIALS P/N 3700-01131 O-RING id 2,175 CSD .130 VITON 75 DURO B

APPLIED MATERIALS P/N 3700-02887 O-RING id 489CSD .070 POLYURETHANE

APPLIED MATERIALS P/N 3700-01208 REV.0 O-RING id 12.984 CSD

APPLIED MATERIALS 0680-00400 SERVICE TOOLS LOTO DEVICE FOR SUPPLEMENTAL CIRCUI

APPLIED MATERIALS P/N 3060-00275 BALL BEARING 12MM BORE X 28MM OD X 8MM W/ VIT

APPLIED MATERIALS P/N 0720-01566

APPLIED MATERIALS P/N 0150-95943 TRANSZORB ASSY (ION SOuRCE)

APPLIED MATERIALS P/N 3950-01029 SPRAY NOZZLE HH-TYPE 1/8 MNPT .040 KYNAR

APPLIED MATERIALS P/N 3880-01129 POLISHER

APPLIED MATERIALS P/N 1313-76400 TOP PLATE BRACKET

WELCH ALLYN P/N M50E021 SOLARC MINIATURE METAL HALIDE ARC LAMP

INTEL PRO/1000 PT DUAL PORT SERVER ADAPTER EXP19402PT **NEW**

CISCO Smart Serial Crossover Cable, 10' (ref.p/n # CAB-SS-2626X-10) **NEW**

MITSUBISHI 4 CHANNEL ANALOG INPUT MODULE FX2NC-64MT...

HP 447047-B21 1/10GB-F VIRTUAL CONNECT ETHERNET MODULE NEW-OTHER

VEXTA NANOSTEP/ BY ORIENTAL MOTOR CO. 5 PHASE DRIVER MODEL DFR1514A

The use of the product:

1.textile machinery,

Moore Automation is a company specializing in the sales of modules and spare parts for world-renowned brands (DCs systems, robot systems, large servo control systems). The company's products include: distributed control systems (DCS), programmable controllers (PLC), MOTOROLA -MVME industrial modules, industrial control communication converters (Anybus), remote output/input modules (RTU), industrial computers (PC), industrial low-frequency screens (IPC), human-machine interface SCSI (50, 68, 80Pin ) AnyBus(Gateway)o The spare parts we sell provide one-year quality guarantee and have undergone strict testing and certification. Now we have become a global sales enterprise of industrial automation spare parts and components.