EPRO PR9268/301-000 PR9268/301 000 PR9268/301000

EPRO PR9268/301-000 PR9268/301 000 PR9268/301000

Product Description:

Manual, gives an overall description of the Bulletin 1305 Adjustable Frequency AC Drive (herein called “the drive”) and provides a listing of key drive options. Additionally, this chapter provides information on receiving and handling the drive. MANUAL OBJECTIVES The purpose of this manual is to provide

the user with the necessary information to install, program, start up and maintain the Bulletin 1305 drive. To assure successful installation and operation, the material presented must be thoroughly read and
understood before proceeding. Particular attention must be directed to the ATTENTION and Important

statements contained within. Chapter 2 provides instructions on how to mount and wire the drive. It also describes how to operate the drive without a Human Interface Module. Read the Motor Cable Length
section on pages 2-13 – 2-16, and the contact closure inputs information in the Control Terminal Block

descriptions on pages 2-19 – 2-21. Chapter 3 defines the display and control panel keys on the optional Human Interface Module. A flowchart is provided to guide the user through the key strokes of the various
menu levels.

Contact Information:

Contact:Miya ( manager)

Email :sales@mooreplc.com
Q Q: 2851195450
Skype: miyazheng520
Mobile:86-18020776792 ( what's app )

Related Product Recommendation:

All drives come equipped with a fault LED. When the fault LED is illuminated it is an indication a fault condition exists. Refer to page 2-3 for the location of the fault LED. Once the fault is properly cleared the LED will return to an off state. Diagnostics As can be seen in Figure 2.3, there are two indicators

provided to display the drive’s status condition. The DC Bus Charge Indicator is a neon bulb that will be illuminated when power is applied to the drive. The Fault Indicator is an LED that will be illuminated if a drive fault condition exists. Refer to details on How To Clear a Fault, below.How To Clear a Fault

Important: Resetting a fault will not correct the cause of the fault condition. Corrective action must be taken prior to resetting the fault. To clear a fault perform one of the following:Cycle power to the drive. Cycle the stop signal to the drive. Cycle the [Clear Fault] parameter.

MKS pressure controller type 652 self tuning pressure controller 652D-BB

CHNT NB1-63 C1, NB1 CIRCUIT BREAKER

AMAT 3300-05050 Ftg Nipple Rdcr NW50xNW40 1.576LG SST

AMAT cable, 30 ft. 0226-31562. 4 pin. EMO cable

New Novellus 10-189321-00 VCR 90 Degree Connection

Edwards 45° Vacuum Elbow, C10512405, new, partially opened

Potter and Brumfield KUP-14D55-24 Lot of 2, 3 Pole relays 24VAC

Stec SEC-4400 MFC, SEC-4400M NF3 Gas, 500 SCCM Range, S4879

ASCO RED-HAT VALVES F3209AK

5 NEW AMAT 0020-77330 DRIVE SHAFT BEARING SPACER

NEW Novellus 17-114726-00 Mounting Plate

3 RF Coax Bulkhead Silver Plated, AMP 225409-1

Horiba stec LF-310A MFC, LF-310A-EVD, TEB, 0.5 g/min, S7865

Horiba stec LF-310A MFC, LF-310A-EVD, TEPO, 0.25 g/min, S0403

Horiba stec LF-410A MFC, LF-410A-EVD, TEOS, 7.0 g/min, AMAT 3030-08008, S0702

Horiba stec LF-310A MFC, LF-310A-EVD, TEPO, 0.2 g/min, AMAT 3030-05748, S0101

Horiba stec LF-310A MFC, LF-310A-EVD, TEPO, 0.25 g/min, AMAT 3030-07719, S0201

Dwyer Photohelic Series 3000MR Differential Pressure Switch/Gage 0-2 inches

OMEGA HYP3-16-1-1/2-K-U-48-RP Hypodermic needle probe

Jennings UCS-300-7.5S, 7.500 VOLTS, used

Stec SEC-4400 MFC, SEC-4400M SF6 Gas, 300 SCCM Range, S5230

New Coax Connector RF 90 Degree TRU-3299

PHOENIX CONTACT D-OTTA 25, CONNECTOR TERMINAL, LOT OF 10

STEC LF-A40M-A-EVD, TEOS 4g/Min, 3332400050

NEW AMAT 0010-37828 Assy Display Board, HF.RF Generator

NEW AMAT 1400-01325 pressure sensor 0-1MPA 1/8PT 3wire 3m LG, SMC PSE520-T01

NEW AMAT 0090-77009 Assy LVDT ZT-910/900 PM2, Sensotec 060-3590-06, ID 327865

AMAT 0010-12123 Assy PLC Controller 200MM Wald CH. A OR

AMAT 0010-08173 ASSY, SOURCE CONTROL SCA, DPN, 200MM, SSGSE-00002

3 AMAT 0200-09373 West Coast Quartz Cover Ring Quartz Alum 150mm New

AMAT 0010-13389 FORTH POSITION BRACKET ASSEMBLY, BDS6 SH

Astex D13449 Microwave magnetron, D13604 waveguide, C13477 isolator, AMAT HDP

The use of the product:

1.open architecture to take advantage of traditional or renewable sources of energy!

2.Customer service in 1-4 hours. If there's any question, please contact with our sales.

3.Experienced technichal support team.

Moore Automation is a company specializing in the sales of modules and spare parts for world-renowned brands (DCs systems, robot systems, large servo control systems). The company's products include: distributed control systems (DCS), programmable controllers (PLC), MOTOROLA -MVME industrial modules, industrial control communication converters (Anybus), remote output/input modules (RTU), industrial computers (PC), industrial low-frequency screens (IPC), human-machine interface SCSI (50, 68, 80Pin ) AnyBus(Gateway)o The spare parts we sell provide one-year quality guarantee and have undergone strict testing and certification. Now we have become a global sales enterprise of industrial automation spare parts and components.