Alloy K-500 Monel K-500 N05500 2.475 WN SO SW blind flange forging disc ring

UNS N05500
Other common names: Alloy K500
Monel K500 is a precipitation-hardenable nickel-copper alloy that combines the excellent corrosion resistance characteristic of Monel 400 with the added advantage of greater strength and hardness. These amplified properties, strength and hardness, are obtained by adding aluminum and titanium to the nickel-copper base and by a thermal processing used to effect precipitation, typically called age hardening or aging. When in the age-hardened condition, Monel K-500 has a greater tendency toward stress-corrosion cracking in some environments than Monel 400. Alloy K-500 has approximately three times the yield strength and double the tensile strength when compared with alloy 400. Plus, it can be further strengthened by cold working prior to precipitation hardening. The strength of this nickel steel alloy is maintained to 1200° F but stays ductile and tough down to temperatures of 400° F. Its melting range is 2400-2460° F.
This nickel alloy is spark resistant and non-magnetic to -200 F. However, it is possible to develop a magnetic layer on the surface of the material during processing. Aluminum and copper may be selectively oxidized during heating, leaving a magnetic nickel rich film on the outside. Pickling or bright dipping in acid can remove this magnetic film and restore the non-magnetic properties.

In what forms is Monel K500 Available?
• Bar
• Rod
Corrosion Resistant Monel K-500
The corrosion resistance of alloy K-500 is substantially equivalent to that of alloy 400 except that when in the age-hardened condition, nickel alloy K-500 has a greater tendency toward stress-corrosion cracking in some environments. Monel K-500 has been found to be resistant to a sour-gas environment. The combination of very low corrosion rates in high-velocity sear water and high strength make alloy K-500 particularly suitable for shafts of centrifugal pumps in marine service. In stagnant or slow-moving sea water, fouling may occur followed by pitting but this pitting slows down after a fairly rapid initial attack.
What are the characteristics of Monel K500?
• Corrosion resistance in an extensive range of marine and chemical environments. From pure water to non-oxidizing mineral acids, salts and alkalis.
• Excellent resistance to high velocity sea water
• Resistant to a sour-gas environment
• Excellent mechanical properties from sub-zero temperatures up to about 480C
• Non-magnetic alloy

In what applications is Monel K-500 used?
• Sour-gas service applications
• Oil and gas production safety lifts and valves
• Oil-well tools and instruments like drill collars
• Oil well industry
• Doctor blades and scrapers
• Chains, cables, springs, valve trim, fasteners for marine service
• Pump shafts and impellers in marine service
Fabrication with Monel K-500
Monel K-500 is readily fabricated by standard commercial procedures.
Welding alloy K-500 is best accomplished by the gas-tungsten-arc welding process. It is recommended that Monel K-500 be annealed when it is welded and that any weldments be stress relieved prior to aging.
Heavy machining of this alloy is best accomplished when the material is in the annealed condition or hot-worked and quenched condition. Age-hardened material however can be finish-machined to close tolerances and fine finishes. Therefore, the recommended practice is to machine slightly oversize, age-harden, then finish to size. During aging, a slight permanent contraction takes place, but little warpage occurs because of the low temperatures and slow cooling rates involved.

We can provide Monel K-500 material in the form of flange, fittings, pipes, fasteners.

Huitong Group was established in 1978. After 38 years'development and innovation,by now,Huitong Group has set up multiple subsidiary companies.Among them,Zhengzhou Huitong Pipe Fitting Co.,Ltd.,with the indepent right of import and export, is mainly engaged in exporting steel pipe and pipe fittings for Huitong Group and assisting another subsidiary company of Huitong Group:Zhengzhou Huitong Machanical Equipment Co.,Ltd., in exporting machanical equipment.

Zhengzhou Huitong Pipeline Equipment Co.,Ltd.,with the strong support of Huitong Group,and years'development and innovation, are more and more professional in technical service and can manufacure products with all kinds of material,shape and size. Especially in elbows, tee, reducer, flange and pipe cap etc., we have gained more than 20 product patent, and hundreds of technology patent. Also,we have gradually taken an ireplacable role in High-pressure,high-temperature and anti-corrosion area. With the continuous construction of engery in China,such as petrol gas,electric power,etc.,our company has become the purchasing center of whole set fittings for such projects.In 2009,a foreign trade team established,is manily engaged in oil gas and electric power projects abroad.By now, our products have been exported to Canada,Malaysia,Parkistan,UAE, Eygpt,the Middle East countries, etc.. We have passed the qualification of ISO9001:2000 and API quality certification system. High-quality products and high-class service are well received by abroad customers in this industry. The unique diversified production line can offer you one-package serive, you can pruchase all complex products from us at one time. What's more, our sufficient material stock and conventional product stock can ensure you receive satisfied product in the shortest time.

With powerful financial strength,advanced managerial concept, excellent marketing service,strict quality control system and integrated marketing team,we would like to develop together with you hand in hand. Adhering to the operation principle of "faith first and clients foremost", we always supply high quality products, complete after-sales service and favorable prices. We sincerely hope to establish long-term cooperation with you on the basis of mutual benefits, reciprocity and common development.