3G SDI CWDM SFP Optical Transceiver Module Digital Video Fiber Optic Lc Connector

3G-SDI CWDM 1270~1610nm 40km Digital Video SFP Optical Transceiver Module

Description:

E-link’s Transceivers are a high performance, cost effective module which have a duplex LC optics interface. They are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA) and Digital diagnostics functions are available via the 2-wire serial bus specified in SFF-8472. The receiver section uses a PIN receiver and the transmitter uses a CWDM DFB laser, up to 16dB link budge ensure this module SONET OC-48 / SDH STM -16 40km application.

• Absolute Maximum Ratings

• Recommended Operating Environment:

• Electrical Characteristics (T_OP = 0 to 70°C, VCC = 3.135 to 3.465 Volts)

Note:

1. AC coupled.
2. Or open circuit.
3. Into 100 ohm differential termination.
4. 20 – 80 %
5. LOS is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.
6. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5MHz up to specified value applied through the power supply filtering network shown on page 23 of the Small Form-factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 14, 2000.

• Optical Characteristics (TOP = 0 to 70°C, VCC = 3.135 to 3.465 Volts)

Note:

1. Compliant with FDA/CDRH and EN (IEC) 60825 regulations (Class 1 Laser Safety).
2. 20-80%.
3. Measured with PRBS 2³¹-1 at 10^-12 BER
4. Measured with PRBS 2⁷-1 at 10^-12 BER
5. Measured with PRBS 2²³-1 at 10^-12 BER

Diagram of Host Board Connector Block Pin Numbers and Names

• Pin Function Definitions

Notes:

1. Circuit ground is internally isolated from chassis ground.
2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3. Should be pulled up with 4.7k - 10 kohms on host board to a voltage between 2.0V and 3.6V. MOD_DEF(0) pulls line low to indicate module is plugged in.
4. Rate select is not used
5. LOS is open collector output. Should be pulled up with 4.7k – 10 kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
6. AC Coupled

SFP Module EEPROM Information and Management

The SFP modules implement the 2-wire serial communication protocol as defined in the SFP -8472. The serial ID information of the SFP modules and Digital Diagnostic Monitor parameters can be accessed through the I2C interface at address A0h and A2h. The memory is mapped in Table 1. Detailed ID information (A0h) is listed in Table 2. And the DDM specification at address A2h. For more details of the memory map and byte definitions, please refer to the SFF-8472, “Digital Diagnostic Monitoring Interface for Optical Transceivers”. The DDM parameters have been internally calibrated.

Established in 2001& headquartered in Shenzhen, E-link China Technology Co., Ltd. (E-link) is a leading Fiber Optic Communication and CCTV Security Transmission product manufacturer in China. Our main products include active equipments including fiber media converters, CCTV fiber converters, CCTV over Ethernet Converters (HD-SDI over Ethernet, HDMI over Ethernet, Power over Ethernet), etc. With rich experience in providing high quality products in telecom and CCTV business, E-link has a large manufacturing base in Shenzhen, able to deliver cost-effective solutions to serve our customers successfully.

E-Link Quality:

• ISO9001 Quality System

• Full-Spectrum environment and electrical testing of all product design

• 48 hours aging test before delivery

• Qualified CE, RoHS, FCC

Since the launch of our products on the domestic market and international market, we have won a good reputation for our high quality products and sincere services. Our products are widely applied to network systems of Telecom, Radio and Television, Public Security, Bank ,ect. To be in line with different needs of different customers, we have people to trace the latest market information so as to keep our products competitive and vital.

Our knowledgeable sales, technical support and engineering staff are dedicated to understanding your requirements and designing products & solutions to meet your needs. We shall be pleased to provide you fiber optical network products with our best price, superior quality and fast delivery.