Armature Plunger K0380 / K0384 Pilot Solenoid Valves for Pulse
Valves
FLY/AIRWOLF Pilot repair kit K0380 K0384 includes O-ring, armature
assembly, armature spring, ferrule.
The product is developed to be used in ambients with temperature
range from –10°C to +80°C
The K0380 plunger is normally equipped with NBR rubber seals. Other
K0384 meterial is fluororubber.
The armature assembly is designed for more than 50x106 cycles.
Specifications:
Plunger and core are made by a magnetic stainless steel specially
designed for solenoid applications.
The plunger is normally equipped with NBR rubber seals. Other
materials like FKM are available upon request. The armature
assembly is designed for more than 50x106 cycles.
The guide tube is made with brass (stainless steel is possible upon
special agreement).
1 . The pulse diaphragm valves are especially designed for dust
collector service applications, combining high flow, long life and
extremely fast opening and closing to produce reliable and
economical operation.
2 . The high flow, angle type bodies in combination with the
special main diaphragm assemblies give the unique operating
features required for dust collector service applications
3 . The design with integral compression fittings will facilitate
installation because there is no need for threaded piping
4 . The high quality diaphragms are reinforced and wear resistant
to guarantee a long operating life, even under harsh conditions
5 . Integral pilot operated valves satisfy all relevant EC
directives
General Data:
Ambient temperature ············································· -
10 °C to + 80 °C
Quality of medium according to ISO 8573-1 ·········· compressed air
class 4, 3, 4
Mounting position
·················································· any ( preferably
plunger in vertical direction )
Technical Data:
GENERAL
Differential pressure 0,35 - 8,5 bar [1 bar = 100kPa]
Ambient temperature range -20 to +85°C
fluid (✷) | temperature range (TS) | diaphragm (✷) |
air | -20 to +85°C | CR (chloroprene) |
ELECTRICAL CHARACTERISTICS
Coil insulation class F
Connector Spade plug (cable Ø 6 - 10 mm)
Connector specification ISO 4400 / EN 175301-803, form A
Electrical safety IEC 335
Standard voltages DC (=): 24V
Competitive Advantage
| Our product features | Our Services Guarantee: |
| 1) Competitive price | 1) Prompt respond (Reply with 24 hours) |
| 2) Good quality | 2) Free Samples (Customer pay for the delivery cost) |
| 3) Professional Packaging | 3) Registration support. |
| 4) Produce according to Customers’ instruction | 4) Photos/videos are available during production. |
| 5) None delay shipment | 5) Loading inspection, and send loading photos before shipment. |
The installment introduction:
1. First, Confirm the pulse valve in good condition and then
installed
2. Pulse valve will be installed directly the outer wall of flange
of gas manifold. The spray pipe across the gas manifold. According
to the drawing and manual, the pulse valve matching appropriate
spray pipe and installation. To avoid the valve install in the air
manifold bottom. If the pulse valve matched trachea and connector,
the connector will be used for sealing purpose only. It can not as
structural support components. It can not rely on the straight
connector fixed spray torch and package. The spray pipe and air
manifold must be fixed independent.
3. To tighten the hard nut, the maximum torque of 20 N*m.Tighten
the trachea, torsion of 20 N*m.
4. The connection control wire needs connect of every electric
control valve seat. Pay attention to the line adown to prevent rain
waterproof. Or through the joint and nylon pipe, it will connect
the pulse valve and electromagnetic assembly boxes of nylon pipe
connection.
5. To ensure that provide compressed air clean and dry. The air
manifold system provides moderate pressure and check for leaks
installation. ( it can brush on soap and water, check whether the
interface is bubble). Pressure was carried out on the air bag
inflated (pressure of the valve is around 0.03 ~ 0. 86 mpa),
recommend for air pressure 0.8 mpa maximum
6. Testing the pulse valve blowing, listening all the pilot valve
whether it is normal operation and whether the pulse blowing sound
is clear.
After-sale Service
We can provide a series of after-sale service, such as product
introduction, mounting, debugging, technical support and so on.
The exhaust chamber volume of improved DMF pulse valve is
increased. The permeability magnetic material of pulse valve is
increased, and also, the materials of structure of diaphragm and
pressure spring are improved, so that the exhaust volume of valve
is increased to raise the magnetic strength and sensitivity as well
as the element reliability and operation stability of pulse valve.
Its service life will be greatly prolonged.
