Fiber Tester PC Control Photoelectric sensors Fiber Tensile
Strength Tester
Application
Fiber Tester PC Control Photoelectric sensors Fiber Tensile
Strength Tester is mainly used a variety of stretch fiber ( Carbon fiber cloth,
carbon fiber cloth, carbon cloth, carbon fiber fabric, carbon fiber
tape, carbon fiber sheet )material products, tensile strength
test,peel, tear, anti-physical properties of shear. While testing
and data processing in accordance with various standards GB, ISO,
JIS, ASTM, DIN, and user-supplied
Main features
Leather Tensile Digital Display Servo Frequency Conversion Tensile
Strength Tester using import photoelectric encoder, controller based on embedded
single chip microcomputer architecture, built-in powerful control
software, measurement, control, and computing, storage in one. Has
automatically calculation stress, and extends rate (needed added
distribution introduction stretch meter), and tensile strength, and
modulus of function, automatically statistics results;
automatically records maximum points, and fracture points, and
specified points of force value or elongation volume; used computer
for test process and the test curve of dynamic displayed, and for
data processing, test end Hou can through graphics processing
module on curve zoom for data again analysis edit, and can print
report, products performance reached international advanced level.
Measuring principle
1, measurement of tensile testing machine is the result of force
sensors, amplifiers and data disposition system measurement.
Learned from information mechanics, small deformation under strain
to an elastic element ε with elastic element is directly
proportional to the force, and elastic form in proportion. A case
study of s-type testing machine sensor if the sensor was pulling
effect of p, because elastic element looks pasted strain, due to
the strain of elastic element is proportional to the size of the
force p, it will strain gage circuit for measuring access, after
measuring the output voltage, and measure the size of the force.
2 after deformation, deformation measurements measurement Setup to
measure, it is used for measuring specimen deformation occurred in
the experiment process. The installation there are two Chuck on,
through the idea of a biography structure and mounted on top of the
measuring installation of optical encoders connected together, when
intervals between two Chuck change, drive the torsion of
photoelectric encoder, encoder will have a pulse signal output. By
the Manager for the disposition of this signal, the deformation of
the sample can be drawn.
3, beam displacement measure the deformation measurement of truth
with much the same thing, is the number of measurements of optical
encoder output pulse to get the displacement of the beam.
structure
Fiber tensile testing machine adopts single-arm structure, the host portion of the column, on
the beam, the beam, the composition of the table, speed control
system installed in the lower part of the table, by the governor
and high precision, wide range, stable performance servo motor
through synchronous toothed belt deceleration system driven ball
screw rotates, the ball screw drive beam to drive accompanied by
stretching (or compression, bending accompanied) to move up and
down, to achieve loading and unloading samples. The structure has a
high stiffness, high efficiency, stable transmission and so on.
Technical Parameters
Items | Specification |
Sensor | Celtron load cell |
Capacity | 10,20,50,100,200kg |
Unit Switchover | G, KG, N, LB |
Display Device | PC and LCD |
Resolution | 1/250,000 |
Accuracy | ±0.5% |
Max. Stroke | 1000mm (including fixture) |
Test Speed | 0.1-500mm/min (adjustable ) |
Motor | Panasonic Servo Motor |
Screw | High Precise Ball Screw |
Elongation Accuracy | 0.001mm |
Power | 220V, 50HZ |
Weight | Approx.75kg |
Accessories | One set tensile clamp, one set Lenovo computer, one piece English
software CD, one piece operation video CD, one piece English user
manual |
The speed tests
Some equipment market in 10 ~ 500 mm / min, and some in the 0.001 ~
500 mm / min, the former general use of common control system, low
cost, rough affect the accuracy; which uses servo system,
expensive, high precision, for flexible packaging business, the
choice of servo system, speed range 1 ~ 500mm / min is sufficient,
this will not affect the accuracy of prices within a reasonable
range.
Buy Considerations
1, should first consider the need to test the material tensile
range.
2, the test stroke problems.
3, the standard configuration issues.
4, the output results.
5, do a pilot project on.
6, the main mechanical configuration
7, test speed.
8, the measurement accuracy.
Our company
Introduction:
Strength Factory Management
Modern equipment and superb process production including laser
cutting panels and wood, ERP systems, production control systems,
cutting automation, our advanced equipment can help us reduce waste
...
Senior Original design Team
4 Research and production base, more than 10 doctoral advisor, more
than 10 High-tech products, more than 50 product patents ...
Exquisite technology, testing agency Quality Control Factory Direct
Sales
Focus on product quality, independent quality inspection
departments to strictly check each process of inspection and pay
attention to customer service, program creative design and later
process production, product quality and quantity ...
Sturdy package turn, professional installation, global distribution
With the national well-known global Express company to ensure the
quality of the goods during the freight and freight time ...
Environmental certification Quality raw materials
Set up a perfect ISO9001 quality assurance system, adhere to the
"standard process operation, using the right data to speak"
principle of total quality management, the quality of physical
assessment standards to "customer expectations"
and ...
