Vehicle Battery Testing Equipment Crush And Penetration Test SAE J2464

Vehicle Battery Testing Equipment Crush And Penetration Test SAE J2464

Product information:

Standard:

Conforms to SAE J2464 Standard (Clause 4.3.3.1: Penetration Test; Clause 4.3.6.1: Crush Test), AIS 038 crush test in page no. 79 of 106 cl.no. 3.2, Nail penetration test in page no. 101 of 106 cl.no. 3.3.2 (a), IEC62133-2012, IS0 12405-4:2018, etc.

Features:

1. The test software has a voltage acquisition function: according to the test requirements of the single battery, until the battery shell breaks or the battery is short-circuited (the internal voltage of the battery becomes 0V), the battery voltage change during the test will be automatically collected. When the voltage is zero, the equipment automatically stops the test.

2. According to the test requirements of the power battery: the test system can first squeeze to 30% of the size of the battery module (i.e., the deformation). Or set a certain pressure value (such as the extrusion force is 20kN). When the extrusion test reaches the set force value and the set pressure holding time is also reached, the equipment stops the test.

3. The sample can be tested according to any of the three conditions of pressure, deformation, and voltage.

4. The three test modes can be used as control variables for any combination of conditions. That is, three or two test conditions can be set at the same time. If any one of the conditions is met, the device will stop the test.

5. The test system can display the speed during the test. The test speed required for the test can also be set in the computer software.

6. The computer operating system is processed in the windows dialog box. The table mode can be planned by yourself. The test data is recorded throughout the process. It provides saving, comparison and tracking functions.

7. The dedicated test control motherboard can record force, displacement and voltage at the same time. The control motherboard will send instructions to the computer in real time, and the control interface will record and monitor the extrusion force, temperature, voltage, speed and deformation in real time. It is convenient to generate reports or export data directly. The control motherboard is easy to operate.

8. During the test, the test function can be controlled by collecting voltage signals. The voltage will change during the battery test. Enter a specified voltage value in the test system, and the system outputs a signal. The extrusion test stops when the set voltage value is reached.

Environmental Requirements:

1. Main power leakage circuit breaker: AC380(1±10%)V (50±0.5)Hz three-phase four-wire + protective ground wire. Install 10㎡ wire, 3P 63A leakage protection switch

2. Power cable: one five-core cable (four-core cable + protective ground wire), about 3 meters long (outside the box)

3. Installation site:

① The ground is flat and well ventilated;

② No strong vibration around the equipment;

③ No strong electromagnetic field around the equipment;

④ No flammable, explosive, corrosive substances and dust around the equipment;

⑤ Avoid direct sunlight or high temperature and humidity;

⑥ The ground load-bearing capacity of the site: not less than 650kg/m2 (prerequisite: the channel size around the equipment is ≥ 600 mm; the load weight is ≤ 500kg);

⑦ There is appropriate space for use and maintenance around the equipment:

⑧ There should be space around the equipment for at least one person to pass through, i.e. ≥600mm;

⑨ There should be space for the equipment door to open and close normally. And there should be no other objects in front of the equipment door.

4. Environmental conditions: Temperature: 20℃±5℃; Relative humidity: ≤85%RH; Atmospheric pressure: 80kPa～106kPa

Technical parameters:

Configuration List

Control Software Function

Safety Protection

Explosion-proof measures

Sinuo is an innovation manufacturing company, specializing in the research and development and sales of laboratory construction and testing equipment for electrical appliances (covering the construction of energy efficiency and performance laboratories, as well as supplementary waterproof testing laboratories, materials flame-retardant laboratories, basic general testing equipment, etc.), Sinuo aims to provide clients with complete laboratory construction, system integration, R&D, rectification and after-sales service, and strive to be the leader of one-stop service for laboratory construction in the field of electrical appliance testing.

Sinuo  products are composed of all kinds of testing equipments as per standards of IEC/ BS/ EN/VDE/UL/ ISO..., such as household appliances testing equipment, energy efficient testing laboratories and comprehensive performance test system for household appliances, battery testing equipment,  automotive testing equipment, luminaries testing equipment,IP code testing equipment, environmental test chamber, flammability test chambers, EMC testing equipment and etc.

Sinuo employees include a highly trained staff of engineers for sales and service, that are committed to offer satisfactory products and prompt service to all home and abroad customers.

Sinuo cooperate with many research institutions and schools to enable our techincal capacities. Sinuo has two own factories, one is in Guangzhou, the other is in Dongguan, and authorized agents and representative offices in Korea, South Africa, Egypt,Pakistan and Philippines.

Sinuo combines all the R/D and production advantages, contributes to provide perfect, high-end and systematic electrical appliance testing laboratory solutions, products and services for corporate customers, universities and third-party laboratories. Our clients include Bureau Veritas, CSA, Intertek, TUV Rehiland, TUV SUD, SGS, etc.