3.5 Inch TFT LCD Touch Screen Full Viewing Angle Mipi 2lane With
CTP
Product Details
| Resolution: | 480 * 640 |
| Size: | 3.5 Inch |
| Viewing Direction: | 9 O'clock |
| TFT Mode: | TFT, Transmissive |
Product Description
| | |
| Display outline size | 64.00 mm * 85.00 mm * 3.00 mm T |
| VA size | 53.28 mm * 71.04 mm |
| Resolution | 480 * 640 Dots |
4 | With /Without Touch screen | With CTP |
5 | Interface | Mipi 2lane |
6 | Brightness | 300 Cd / M2 |
7 | Driver IC | ST7796/ ILI9488 |
Core parameters and features
Size / Resolution: 3.5 inches, common resolutions are 320×480 or
640×480 (varies by model), with moderate pixel density, clear
text/icon display.
Display technology: Usually IPS full-viewing angle, with an angle
range of approximately 178°, good color and contrast performance,
no obvious color deviation when viewed from the side.
Interfaces: MIPI DSI 2-lane, low power consumption, high speed
rate, strong anti-interference ability, easy to connect directly
with the main control chip, reducing wiring and EMI.
Touchscreen: Capacitive (CTP), supports multi-touch (such as 5
points / 10 points), sensitive response, supports gesture
operations; CTP usually communicates with the main control through
I²C interface, facilitating integration and calibration.
Brightness / Contrast: Common brightness is 300-500 nits, some
high-brightness models can reach above 700 nits, suitable for
indoor and semi-outdoor use; typical contrast value is about
700:1-1000:1.
Operating temperature: Industrial grade is usually -20℃ to +70℃,
storage temperature -30℃ to +80℃, suitable for most industrial and
vehicle environments.
Form and installation: Module thickness is usually around 3.9-4.6
mm, paired with FPC/FFC flexible ribbon cables, facilitating
compact installation.
Typical application
Embedded devices: such as handheld terminals, industrial
controllers, instruments and meters, smart home panels, etc.
Vehicle HMI: vehicle central control, air conditioning control,
vehicle camera display, etc.
Consumer electronics: portable medical devices, handheld game
consoles, smart doorbells, etc.
FAQ:
1. I want the LCD display 8 digits and the outline size is
65x30x2.8mm………?
Answer: No problem. Firstly, please kindly send us your
specification/ drawing paper
If you have not the specification, you can also provide your samples; we will recommend the suitable
one
if it is standard products. Or we can customize for you based on
your own requirement.
2.This LCD is just what we want, but it is big size, do you have
any smaller size? And the display content need to be changed a little.
Answer: For the segment type LCD module, if you need modify the
outline size or display content,
a new LCD glass module is need. We have to open new tooling for you.
3. This LCD display is HTN type, but I want STN type,can you make?
Answer: That’s all right . we can change for you as per you request.
4. I want customize a new LCD module. Can you do?
Answer: Yes, we can. Please send your drawing paper. If you have
not, please advise me the outline size
of the LCD display, display information( Glass thickness, Polarizer, Display Type, Connector mode,
Storage Temp. Operating Temp. Supply Voltage, Viewing direction, drive condition), we can customize for you.
5. What is leading time for tooling?
Answer: General speaking, it will cost 15 to 25 days after drawing
paper confirmation and tooling charge payment,
we can report you the exact time when you confirm the drawing paper.
6. Can you send us samples for checking?
Answer: Yes,. Samples order is available.
7. What is the Leading Time?
Answer: If we have stock for the standard ones, the leading time is
one day after payment. If it is the mass production for
special ones, the leading time is about 15-30 days. suppose we can
finish earlier, we will report the information in advanced.
