Moog Servo Valve with 25mm-45mm Shaft Diameter Electro-hydraulic Control and Hydraulic Oil Fuel for Precision Flow Regulation

D761-2612/D791-5009 H19J0GBEVAL
D761-2619/D791-4028 H10J0GAEVAL
D061-8411/D662-4010 J15HOBA4VB1
D061-8412/D663-4007 J15HOBB4VB1
G761-3002 MOOG electro-hydraulic servo valve flow control hydraulic

FAQ:

Frequently Asked Questions (FAQ): Moog Electrohydraulic Servo Valves

1. What is an Electrohydraulic Servo Valve?

An electrohydraulic servo valve is a precision component that acts as an interface between the electrical control system and the hydraulic power system. It receives a low-power electrical analog signal and converts it into a proportional, high-power hydraulic output (flow and pressure). This makes it a crucial control core in electrohydraulic servo systems, responsible for both electrical-to-hydraulic signal conversion and power amplification .

2. How does a Moog Servo Valve work?

A Moog servo valve typically consists of a polarized electrical torque motor and a two-stage hydraulic amplifier .

• First Stage: The torque motor deflects an armature and a flapper attached to it. This flapper moves between two nozzles, creating variable orifices that control the pressure on either end of the second-stage spool .

• Second Stage: The differential pressure moves the spool, which then controls the flow of hydraulic fluid to the actuator. A feedback spring, connected to the flapper and engaging the spool, creates a force that balances the input signal torque, ensuring precise spool positioning proportional to the electrical command .

3. What are the key installation requirements?

Proper installation is critical for performance and longevity.

• Filtration: Install a precision filter with a rating of 5 microns or less upstream of the servo valve. The hydraulic fluid cleanliness should be maintained at a maximum ISO DIS 4406 Code 16/13, with Code 14/11 recommended .

• System Flushing: Before installing the servo valve, the entire hydraulic system must be thoroughly flushed to remove contaminants. Use a flushing manifold and circulate fluid under conditions simulating normal operation .

• Mounting: The valve can be mounted in any orientation, ensuring port alignments match the manifold. The mounting surface should be clean, smooth, and flat. Use the specified screws and torque them to 96 inch-pounds .

• Connections: Use O-ring seal connections (e.g., SAE J1926) and avoid welded fittings. Prefer crimped or 24-degree cone type connections .

4. What are common faults and how can I troubleshoot them?

Common faults can be categorized as follows :

• Electrical Faults: Include power supply failure, cable damage, or poor contact. Check the supply voltage, cables, and connectors.

• Mechanical Failures: Such as a stuck valve spool, damaged springs, or worn seals. Regular inspection, cleaning, lubrication, and part replacement are necessary.

• Hydraulic Faults: Including oil contamination, low oil level, or oil leaks. Regularly replace and filter the oil, check oil levels, and repair leaks.

• Valve Oscillation: Unstable operation may be caused by issues with the servo valve's resolution, wear of the valve port, or incorrect control system parameters.

Here is a brief troubleshooting chart based on symptoms :

Potential Trouble Probable Cause
Servovalve does not follow input command 1. Open coil or coil leads.
2. Clogged inlet filter.
Poor response 1. Clogged inlet orifices or nozzles.
2. Partially clogged filter.
3. "Sticky" spool.
No response to electrical signal Shorted coil assembly.
Low flow gain 1. Incorrect null adjustment.
2. Partially plugged orifice or filter.

5. What does daily maintenance involve?

Routine maintenance focuses on preventing common faults :

Quanzhou Yisenneng Hydraulic Electromechanical Equipment Co., Ltd. has been established for many years and has now developed into an international trading company supplying various hydraulic machinery parts, oil pumps and valves. We are one of the few Chinese companies with multiple products and channels. Main focus: quality assurance! The price is the lowest in the industry! Quality management procedures are implemented in accordance with international standards and are implemented throughout the production process. In terms of channels, we have gathered the most complete variety of products in the world; in terms of quality, all products meet international standards; the lowest price in the industry is the highest; the fastest delivery on credit, and a complete after-sales system; remember Good service is the key to cooperation with customers. We strive to achieve high quality standards, provide competitive prices, and ensure timely delivery. In this way, our products have been recognized by the market and satisfied by customers in the past years. Our goal is to meet the needs of our global customers. Here you can enjoy a one-stop shopping experience, the customer is God, you want all of us, I wish you a happy shopping trip.