Rexroth A4VSO355 Axial Piston Pump 280 Bar Pressure New

A4VSO355DRG/22R-VPB13N00 A4VSO355DRG/22R-PPB13N00 A4VSO355DFR/22R-VPB25N00
A4VSO355DFR/22R-VZB13N00 A4VSO355DFR/22R-PZB13N00 Industrial variable high-pressure A4VSO355 German Rexroth piston pump

FAQ;

Maintenance & Troubleshooting

Q8: What does daily/regular maintenance involve?

• Keep the pump exterior clean from dust and oil污.

• Check oil levels before start-up and during operation.

• Listen for abnormal noises during operation, which may indicate internal issues like part wear or looseness.

• Regularly record operating parameters like pressure, flow, and temperature to monitor health.

• Change fluid filters periodically (e.g., every 1000 hours or as per conditions).

• Check and replace worn or aged seals.

• Follow lubrication requirements for various points.

• Inspect the coupling for looseness or wear.

Q9: The pump outputs insufficient flow or no flow at all. What could be wrong?

Primary reasons are:

• Insufficient Inflow: Caused by high suction line resistance, low oil level, excessive pump speed, or a clogged inlet strainer/suction line.

• Excessive Leakage: Worn internal parts (pistons, cylinder block, port plate) leading to high internal leakage.

• Swash Plate Angle: The swash plate angle might be set too small, minimizing displacement.

Q10: Why is there flow output when the control signal is at zero (neutral)?

This is often due to the control mechanism being off its neutral point. The cause can be a misadjusted, loose, or damaged controller. The solution is to re-zero, tighten, or replace the controller.

Q11: The output flow fluctuates. What is the cause?

Flow instability, often accompanied by pressure fluctuations, is frequently related to issues within the control piston mechanism. This can be due to contamination scratching the control piston, a weak or damaged control amplifier spring, or other damaged components. Addressing this usually requires disassembling the pump to inspect, repair, or replace the affected parts, and possibly increasing damping or spring stiffness.

Q12: The pump is leaking oil externally. Where should I look?

External leaks can originate from:

• Shaft Seal: Damaged or worn-out shaft seal.

• Pipe Connections: Loose hose connections, damaged fittings, or aged/ cracked sealing washers.

• Case Ports: Leaks from the variable mechanism cover bolts due to loose bolts or破损 seals.

• Case Imperfections: Rarely, sand holes in cast iron casings or poor welds.

• High Case Pressure: Excessive internal leakage can pressurize the case, damaging seals or pushing them out. Ensure the case drain line is unrestricted, of adequate size, and not too long.

5. Special Topics & Long-Term Storage

Q13: When is bearing flushing necessary, and what is the flow rate?

Bearing flushing is recommended for: using special HF fluids, operating at viscosity/temperature limits, or for pumps installed vertically (shaft up). Refer to technical documentation for specific flow rates, which range from ~3 L/min for size 40 to ~40 L/min for size 1000.

Q14: How should I handle the pump for long-term storage?

If the pump is to be stored for an extended period:

• Drain all hydraulic fluid from the pump casing.

• Perform a thorough cleaning and drying.

• Apply a rust preventive agent.

• Store in a dry, ventilated place.

• Before putting back into service, perform a comprehensive inspection and maintenance check.

------

This FAQ is based on technical information from publicly available sources regarding Bosch Rexroth A4VSO series pumps. Always prioritize the official manufacturer's documentation and specifications for your specific pump model.

Quanzhou Yisenneng Hydraulic Electromechanical Equipment Co., Ltd. has been established for many years and has now developed into an international trading company supplying various hydraulic machinery parts, oil pumps and valves. We are one of the few Chinese companies with multiple products and channels. Main focus: quality assurance! The price is the lowest in the industry! Quality management procedures are implemented in accordance with international standards and are implemented throughout the production process. In terms of channels, we have gathered the most complete variety of products in the world; in terms of quality, all products meet international standards; the lowest price in the industry is the highest; the fastest delivery on credit, and a complete after-sales system; remember Good service is the key to cooperation with customers. We strive to achieve high quality standards, provide competitive prices, and ensure timely delivery. In this way, our products have been recognized by the market and satisfied by customers in the past years. Our goal is to meet the needs of our global customers. Here you can enjoy a one-stop shopping experience, the customer is God, you want all of us, I wish you a happy shopping trip.