Model: Temperature Humidity Chamber |
EC4018 |
EC7018 |
EC4034 |
EC7034 |
EC4060 |
EC7060 |
EC4100 |
EC7100 |
EC4150 |
EC7150 |
| Test Space Volume(L) | 190 | 335 | 600 | 990 | 1540 |
| Temperature Test Parameters: |
| Temp. Range (℃) | -42/+180 | -72/+180 | -42/+180 | -72/+180 | -45/+180 | -72/+180 | -45/+180 | -73/+180 | -42/+180 | -73/+180 |
Temp. Constancy (℃) | ±0.1-±0.5 |
| Temp. Homogeneity (℃) | ±0.5-±2.0 |
| Heating Rate(℃/min) | 4.0 | 4.0 | 3.2 | 3.0 | 4.0 | 4.0 | 4.0 | 4.0 | 3.5 | 3.5 |
| Cooling Rate (℃/min) | 4.0 | 3.0 | 4.0 | 3.0 | 3.0 | 2.5 | 3.0 | 2.5 | 2.5 | 2.3 |
Temp. Max. Thermal Compensation (W) | 2800 | 1500 | 2800 | 1500 | 1500 | 2500 | 4500 | 3000 | 4200 | 3000 |
| Climate Test Parameters: |
| Dewpoint Temp.Range (℃) | +4(-3)-+94 |
| Humid. Range (%RH) | 10-98 |
| Humid.Constancy (%RH) | ±1.0-±3 |
| Temp. Constancy (℃) | ±0.1-±0.3 |
| Temp. Homogeneity (℃) | ±0.5-±2.0 |
| Temp and Humid Max.Thermal Compensation (W) |
400 |
400 |
400 |
400 |
500 |
500 |
500 |
500 |
500 |
500 |
| Power | AC380V±10%,50HZ,3/N/PE |
Optional Accessories: | Standard Version: |
Independent sensors for specimen protection(NE60519-2.1993) | 3 Power outlets for specimens |
1 Entry port Φ100mm | Left and right entry ports Φ50mm |
Drier filter for compressing air | Silicon Stoppers for entry ports |
Automatic water supply device | 2 Stainless steel shelves |
Nitrogen gas auxiliary device | 1 Water tank with 20L |
Water-Cooled unit | 1 Water filter |
Spare parts package | |
E-management and cyber software | |
| Video monitor system | |
| APP for mobility management | |
Load condition requirements:
•The total mass of the load placed per cubic meter of studio volume
shall not exceed 80KG
•The load of each layer of test material placement rack shall not
exceed 20KG
•The load physical volume is not greater than 2/5 of the studio
volume
•At any section perpendicular to the wind direction of the inner
circulation, the total area of the sample load
should not be greater than 1/3 of the cross-sectional area of the
studio in this direction. Oversized sample
load will affect the air balance and smooth of the studio
Temperature Humidity Chamber Standards:
•IEC60068-2 temperature and humidity test method 8,
MIL-STD-202G-103B humidity test
Structure of the way:
Integral, (test chamber door direction is in front) front for the
studio, refrigeration unit, after the electric
control cabinet and electric control device, the main control
interface is located in front of the test chamber
door, expansion control panel is located in the right back of the
test chamber. The door is open in the width
direction. At the back of the studio, there are circulating air
duct system and air conditioning system: centrifugal
fan blade, air guide device, heater, humidifier, refrigeration heat
exchanger, temperature and humidity sensor.
