| Base parameters | |
| Measuring medium | Liquids, fluids, gases (compatible with contact materials) |
| Measuring range | -100kPa~0~6MPa (see range selection table for details) |
| Type of pressure | Gauge pressure, absolute pressure, negative pressure |
| Temperature compensation | Standard (temperature compensation -10-70°C) 0.25%FS, 0.5%FS
Optional (temperature compensation -40-80°C) 0.1%FS, 0.25%FS (Note)
Note: The range range is ≤ 10kPa, and the temperature compensation
range is -10~70°C |
| Accuracy class | 0.1%FS,0.25%FS,0.5%FS |
| Response frequency | 5Hz,30Hz,100Hz |
| Stable performance | ± 0.1% FS/year |
| Temperature drift | ±0.01%FS/°C (temperature compensation range) ±0.05%FS/°C (outside
temperature compensation range) |
| Overall weight | No display≈ 190g has a display ≈ 270g |
| Degree of protection | IP65 (no display) IP54 (with display) Note: The above protection
level refers to the electrical connection is achieved after the
electrical connection is complete |
| Output power | |
| Output signal | 4~20mA,RS485,0~10VDC,0~5VDC,1~5VDC,0.5~2.5VDC |
| Power supply range | 9～36VDC,15～36VDC,3～5VDC |
| Power range | |
| Voltage type | ≤0.02Us(W),≤0.008Us(W),≤0.001Us(W) |
| Current type | ≤0.02Us(W) |
| Digital | ≤0.02Us(W),≤0.015Us(W) |
| Load characteristics | |
| Voltage type | ≥10kΩ |
| Current type | No display load≤{(US-7.5)÷0.02}Ω
with display load≤{(US-12)÷0.02}Ω (US=supply voltage) |
| Environmental conditions | |
| Media temperature | -40～85℃ |
| Ambient temperature | -40～85℃ |
| Ambient humidity | 0%~95%RH(no condensation, no condensation) |
| Overload capacity | |
| Overload pressure | 300%FS,200%FS,12kPa,50kPa,300kPa,480kPa,750kPa,800kPa,1.2MPa,2MPa,3MPa,5MPa |
| Burst pressure | 600%FS,500%FS,400%FS,20kPa,200kPa,600kPa,900kPa,1.25MPa,2MPa,3MPa,5MPa,9MPa,12.5MPa |
| Overall material | |
| diaphragm | 316L stainless steel (contact with the medium to be measured) |
| Process connection | 304 stainless steel (contact with the medium to be measured) |
| enclosure | 304 stainless steel |
| Seals | Nitrile rubber (contact) fluoroelastomer (seen pressure and
blasting chart (contact with the medium to be measured) |
| Display the shell | ABS Engineering Plastics (LED Display) |
| Hirschmann joints | ABS engineering plastics |
| Mechanical stability | |
| Seismic performance | 10g(20… 2000Hz) conforms to IEC60068-2-6 standard |
| Impact resistance: | 500g/ms conforms to IEC60068-2-27 standard |
| Electrical protection | |
| Short-circuit protection | perpetual |
| Anti-polarity protection | No damage, but not working |
| Insulation resistance | ≥100MΩ500VDC |
| Dielectric strength: | 500VAC |
| Output limits | |
| The output is minimal | 4mA,0,0.001VDC,0.05VDC |
| Output maximum | 20mA,2000,10VDC,5VDC |
