Jaw Crusher Machine Sand And Gravel Production Chemical Industry
New Pattern
Product Introduction
The jaw crusher is commonly known as Ebo or Tiger Mouth. It is a
crusher composed of two jaw plates, a moving jaw and a stationary
jaw, which simulate the movement of animals and complete material
crushing operations. It is widely used in industries such as mining
and smelting, building materials, highways, railways, water
conservancy, and chemical engineering. Suitable for crushing
various ores and bulk materials. Effectively solving the problem of
high operating rate and no maintenance time caused by low output of
the original limestone crusher, it can complete the crushing of
large blocks of limestone.
Product Features
1. Low noise and less dust.
2. Its crushing ratio is large, and the product particle size is
uniform.
3. Simple structure, reliable operation, and low operating costs.
4. The lubrication system is safe and reliable, with convenient
component replacement and simple equipment maintenance.
5. The crushing chamber is deep and has no dead zone, which
improves the feeding capacity and output.
6. Equipment energy-saving: Single machine energy-saving by 15% to
30%, system energy-saving by more than twice.
7. The adjustment range of the discharge port is large, which can
meet the requirements of different users.
Preparation Before Use
1. The lubrication of the bearings should be carefully checked for
good condition, and there should be sufficient lubricating grease
at the connection of the inner bracket of the bearings.
2. All fasteners should be carefully checked for complete
tightness.
3. Whether the protective devices are in good condition, any unsafe
phenomena should be immediately eliminated.
4. Check if there is any ore or other debris in the crushing
chamber, and if there is, it should be eliminated immediately.
Product Launch
1. Only after inspection and verification of the normal condition
of the machine and transmission parts can it be started.
2. This machine can only be started without load.
3. After starting, if any abnormal situation is found, the vehicle
should be stopped immediately. Only after identifying the cause and
eliminating the hidden danger can it be restarted.
Maintenance And Use Of Products
1. The crusher can only be fed after normal operation.
2. The material to be crushed should be evenly added to the
crushing chamber, and side feeding should be avoided to prevent
sudden changes in load or unilateral increase.
3. Under normal working conditions, the temperature rise of the
bearing should not exceed 35 ℃, and the maximum temperature should
not exceed 70 ℃. Otherwise, it should be stopped immediately to
identify the cause and eliminate it.
Product Lubrication
1. Regular attention and timely lubrication of the friction surface
can ensure the normal operation of the machine and extend its
service life.
2. The lubricating grease used in this machine should be determined
based on the location of use, temperature, and other conditions.
Generally, calcium based, sodium based, or calcium sodium based
lubricating grease can be used.
3. The lubricating grease added to the bearing seat is 50-70% of
its volume and must be replaced every three months; When replacing
with new oil, clean gasoline or kerosene must be used to clean the
dirt inside the bearings and bearing seats.
4. Before starting the machine, lubricating grease must be added to
the contact area between the elbow plate and the elbow pad.
Parameter Table
| Model | Size of feed inlet(mm) | Maximum feed(mm) | Adjustment range of discharge port | Processing capacity(t/h) | Power(kw) | Size(mm) |
| TTJ13-59-86 | 150×250 | 125 | 10-40 | 1-5 | 5.5 | 758*58*794 |
| TTJ13-59-87 | 250×450 | 210 | 20-60 | 5-20 | 15 | 1500*1400*900 |
| TTJ13-59-88 | 250×750 | 210 | 15-70 | 15-30 | 22 | 1400*1300*1350 |
| Note: The above parameters are for reference only, please refer to
the actual product for details. |
