9.22g/Cm3 Nickel Alloy Flanges Hastelloy B2 Flanges For Calcining Furnace Heat Treatment

Nickle Alloy Flat Welding Flange Hastelloy B2 Calcining Furnace Heat Treatment

Nickle Alloy Flange, also known as a flange rim or flange, is a part that connects pipes to each other at the ends, and it is also used on equipment inlets and outlets for connecting two pieces of equipment, such as a reducer flange. A flange connection or flange joint refers to a detachable connection consisting of a flange, gasket, and bolt, which together form a combined sealing structure.

Welding Process:

• Required Equipment: A set of manual arc welding equipment, one handle-type angle grinder, one electric air hammer, and one straight edge.
• Folding Welding Preparation: 1. Check and adjust the equipment to ensure normal operation; 2. Prepare φ4.0 J402 welding rods, which are preferably dried at 300°C - 350°C for one hour.
• Folding Welding Process: 1. Assemble the cone and the large flange according to the drawing requirements, then divide the large flange into 8 equal parts; 2. Welding due to the thicker flange and larger groove, the use of segmental symmetrical, multi-layer welding is adopted.
• Folding Welding Quality Requirements: The weld strength must at least match the strength of the base material. The weld surface should be flat and smooth, without defects such as burn-through, porosity, welding leaks, slag inclusion, undercutting, or incomplete welding. The weld reinforcement height should be less than 2mm.
• Folding Notes for Attention: 1. When welding the base layer, always use J506 welding rod manual surfacing and welding with a small current. Strictly follow the welding process; 2: After welding each position, use a level to check the deformation of the flange plane; 3: While welding, use the air hammer to strike the weld to eliminate stress.

Hastelloy B2 is a grade of Hastelloy whichis a nickel-molybdenum alloy. There are manydifferent grades of Hastelloy, which includesB-2. Grades of Hastelloy have each been optimized for a specific purpose. Molybdenummakes Hastelloy harder and stronger at hightemperatures. This alloying element and thecharacteristics itimbues into the material alsomakes it great for welding applications. Thesenickelalloys are easily fabricated and formed.They also exhibit good ductility and are able tobe cold worked. All grades of Hastelloy are considered to be acorrosion resistant alloy because each gradeexhibits superior resistance to variouscorrosive environments.Hasteloy has outstanding resistance to highly oxidizingcorrosives such as oxidizing salts and reducingagents, making it a great alloy to specify for applications used in moderate to severe corrosive environments.

APPLICATIONS

Hastelloy B2 is used for most chemicalprocess applications in the welded condition.gasoline retining.

DESCRIPTION

Hastelloy B2 is a nickel-base wrought alloywith excellent resistance to hydrochloric acidat allconcentrations and temperatures
Therefore, it has great resistance to stress corrosion cracking and pitting.lt also withstands hydrogen chloride, sulfuric, aceticand phosphoric acids.

FORMS

Coil -Sheet, Strip, Foil Wire -Profile, Round,Flat, Square

MECHANICAL PROPERTIES AT ROOM TEMPERATURE

PROPERTIES:

ANNEALED TYPICAL
Ultimate Tensile Strength: 110 KSl min (758MPa min)
Yield Strength: 51 KSl min (352MPa min )Elongation: 40 % minHardness: Rb 100 max

PROPERTIES:TEMPERED
Hastelloy B2 can be cold worked to varioustempers. Contact Ulbrich Technical Service foradditionalinformation.

FINISHES

• Hot rolled annealed and descaled. lt isavailable in strip, foil and ribbon. lt is used forapplications where a smooth decorative finish is not required. 2D- Dull finish produced by cold rolling, annealing and descaling. Used for deep drawn parts and those parts that need to retain lubricants in the forming process. #2B-Smooth finish produced by cold rolling, annealing and descaling.A light cold rolling pass is added after anneal with polished rollsgiving it a brighter finish than 2D. #BA- Bright annealed cold rolled and bright annealed #CBA- Course bright annealed cold rolledmatte finish and bright anneal
• Cold Rolled #2BA- Smooth finish produced by cold rollingand bright annealing.A light pass using highlypolished rolls produces a glossy finish.A 2BAfinish may be used for lightly formed applications where a glossy finish is desired inthe formed part. Polished -Various grit finishfor specific polish finished requirements.

Chemical Composition:

Designantion and standards:

The typical mechanical properties of HastelloyC-4:

Processing Flow Chart:

Hunan Dinghan New Material Technology Co.,Ltd. (DINGSCO) specialized in Nickel Based Corrosion Resistant and High Temperature alloys products which used in the world’s most technically demanding industries and applications.

We have complete advanced technology facilities to produce best quality alloys to meet exacting your specifications such as VIM (Vacuum lnduction Melting) furnace to provide high purity Alloys,ESR (Electro Slag Re-melting) furnace to enhances the structure and purity of the Alloys, and CNC machining equipments (Lathe, Wire cutting, Drilling,Milling) to provide high precision finished products.

We are dedicated to providing our customers with best quality products,fastest possible deliveries, most competitive prices of Nickel Based Corrosion Resistant and High Temperature alloys in bars,rods,forged flanges, valve parts, forged shapes (shafts, discs, blocks, hubs,rings, cylinders and tailor shapes) according to ASTM,ASME,API,AMS, NACE and other industry standards.

We can help you gain a competitive edge in the market by responding to a rush quote in less than 24 hours and even complex requests for price and delivery quotations are responded to within 48 hours.