The Cisco Catalyst 3650 Series Switch, with Cisco StackWise-160
Technology, can stack 9 switches and support up to 160 Gpbs stack
bandwidth. The WS-C3650-24TS-E integrates with 24 Ethernet ports and 4 x 1G SFP uplink ports in
IP Service feature set.
Quick Specs
Figure 1 shows the appearance of the Cisco C3650-24TS-E switch.
Table 1 shows the Quick Specs.
| Product Code | WS-C3650-24TS-E |
| Enclosure Type | Rack-mountable - 1U |
| Feature Set | IP service |
| Uplink Interfaces | 4 x 1G SFP |
| Ports | 24 x 10/100/1000 Ethernet ports |
| Maximum stacking number | 9 |
| Stack bandwidth | 160 Gpbs |
| Forwarding Bandwidth | 41.66Mpps |
| Switching Capacity | 88 Gbps |
| RAM | 4 G |
| Flash Memory | 2G |
| Number of AP per switch/stack | 50 |
| Number of wireless clients per switch/stack | 1000 |
| Dimensions | 44.5 cm x 44.5 cm x 4.4 cm |
| Package Weight | 17.49 Kg |
High Availability
In addition to StackWise-160, the Cisco Catalyst 3650 Series
supports high-availability features including but not limited to
the following:
●Cross-Stack EtherChannel provides the ability to configure Cisco
EtherChannel technology across different members of the stack for
high resiliency.
●Flexlink provides link redundancy with convergence time less than
100ms.
●IEEE 802.1s/w Rapid Spanning Tree Protocol (RSTP) and Multiple
Spanning Tree Protocol (MSTP) provide rapid spanning-tree
convergence independent of spanning-tree timers and also offer the
benefit of Layer 2 load balancing and distributed processing.
Stacked units behave as a single spanning-tree node.
●Per-VLAN Rapid Spanning Tree (PVRST+) allows rapid spanning-tree
reconvergence on a per-VLAN spanning-tree basis, without requiring
the implementation of spanning-tree instances.
●Switch-port autorecovery (Err-disable) automatically attempts to
reactivate a link that is disabled because of a network error.
High-Performance IP Routing
The Cisco Express Forwarding hardware routing architecture delivers
extremely high-performance IP routing in the Cisco Catalyst 3650
Series Switches:
●IP unicast routing protocols (static, Routing Information Protocol
Version 1 [RIPv1], and RIPv2, RIPng, Enhanced Interior Gateway
Routing Protocol [EIGRP] stub) are supported for small-network
routing applications with the IP Base feature set. Limited static
routing with the LAN Base feature set. Equal-cost routing
facilitates Layer 3 load balancing and redundancy across the stack.
●Advanced IP unicast routing protocols (Open Shortest Path First
[OSPF], EIGRP, Border Gateway Protocol Version 4 [BGPv4], and
Intermediate System-to-Intermediate System Version 4 [IS-ISv4]) are
supported for load balancing and constructing scalable LANs. IPv6
routing (OSPFv3, EIGRPv6) is supported in hardware for maximum
performance. OSPF for routed access is included in the IP Base
image. The IP Services feature set is required for full OSPF,
EIGRP, BGPv4, and IS-ISv4.
●Policy-based routing (PBR) allows superior control by facilitating
flow redirection regardless of the routing protocol configured.
Virtual routing and forwarding (VRF)-Lite enables a service
provider to support two or more VPNs, with overlapping IP
addresses. The IP Base feature set is required.
●Protocol-independent multicast (PIM) for IP multicast routing is
supported, including PIM sparse mode (PIM‑SM), PIM dense mode
(PIM-DM), PIM sparse-dense mode, and source-specific multicast
(SSM). The IP Services feature set is required.
●IPv6 addressing is supported on interfaces with appropriate show
commands for monitoring and troubleshooting.
