167Kva Single Phase Pole Mounted Transformer Oil Immersed 34.5KV To
240V ANSI IEEE Standards Power Distribution Transformer
WINLEY Electric's single phase pole mounted transformers available
in ratings from 10-333 kVA.With voltage ratings up to 34.5
kV,Meeting ANSI/IEEE C57, IEC60076 and other standards.Get a Quote
in Minutes.
Pole-mounted transformer factory photos
Pole Mounted Transformer Main data
| Transformer Type | Overhead Distribution Transformer, Conventional Type |
| Transformer Configuration | Liquid Filled Pole Mounted |
| Phase | Single Phase |
| Capacity | 167 KVA |
| Primary Voltage | 34500V |
| Primary Voltage Switch | N/A |
| Primary Voltage Class | 35 kV Class |
| Primary Phasor | Delta |
| Primary BIL | 200 kV |
| Secondary Voltage | 120/240V (L-N-L) |
| Frequency | 60 Hz |
| Temperature Rise | 65°C |
| Insulation Rating | Class E Insulation - 120°C, 248°F |
| Efficiency Standard(s) | Meets DOE 2016 Standards, Meets CSA Standards Meets ANSI/IEEE
Standards |
| Winding Material | Copper |
Pole-mounted transformer Standard Features
- Lifting lugs
- Arrester mounting pads
- High-voltage porcelain bushing(s) with eyebolt terminals
- Low voltage bushing insulators are available in fiberglass
reinforced polyester material or porcelain (both eyebolt and spade
terminals)
- Low-voltage neutral grounding strap (furnished on 10 – 50 kVA
single HV bushing units)
- ANSI support lugs (hanger brackets)
- Cover has 15 kV dielectric insulation and increased resistance to
corrosion. The cover is sloped 15°, preventing water from
collecting and thereby reducing the chances of corrosion and
leaking.
- Self-venting and resealing cover that eliminates the need for an
auxiliary pressure-relief device and offers increased safety
through higher tank withstand
- Wound core with step-lap joints for increased efficiency and lower
noise levels.
- Core/coil bolts in pads are 180° apart
- Embossed low-voltage leads
- Oil fill-plug
- Cover ground-strap
- Tank ground-pad
- Primary protective link
- Surge arrester
- Secondary circuit breaker
- Secondary breaker operating handle with emergency overload reset
- Laser-etched, anodized, aluminum nameplate with bar-coded serial
number
Pole-mounted transformer Technical drawings
Pole-mounted transformer Specifications
| Single-phase pole mounted transformer |
| Rated Cap acity(kVA) | High | Low Voltage(v) | Connection Symbol | Standard | Short-circuit impedance(%) | Efficiency |
| Voltage(v) | (%) |
| 10 | 4160
7200
12000
12470
13200
13800
19920
24940
34500 | 110
220
230
400
480 | II0,II6 | IEEE/ANSI/ DOE | 1.8-4% | 98.7 |
| 15 | 98.82 |
| 25 | 98.95 |
| 37.5 | 99.05 |
| 50 | 99.11 |
| 75 | 99.19 |
| 100 | 99.25 |
| 167 | 99.33 |
| 250 | 99.39 |
| 333 | 99.43 |
| 500 | 99.49 |
Pole-mounted transformer Ratings
- Meets/Exceeds DOE 2016 Efficiency Ratings
- Meets/Exceeds CSA Efficiency Ratings
- Complies with ANSI / IEEE C57 12.00
- Complies with ANSI / IEEE C57 12.20
- Complies with ANSI / IEEE C57 12.30
- Complies with ANSI / IEEE C57 12.31
- Complies with ANSI / IEEE C57 12.35
- Complies with ANSI / IEEE C57.12.70
- Complies with ANSI / IEEE C62.11
- Complies with ANSI / IEEE C62.22
- Complies with ANSI / IEEE C2
- Complies with ANSI / IEEE C37.47
- Complies with ANSI Z535.4
- Complies with ASTM D3487
- Complies with ASTM D6871
- Complies with 10 CFR Part 431
- Complies with CSA C2.206
- Complies with CAN / CSA C50
- Complies with CAN / CSA C233.1-87
- Complies with CAN / CSA C802.1-13
Pole-mounted transformer Production process
FAQ
1. Q: Can I have a sample order?
A: Yes, we welcome sample order to test and check quality.
2. Q: What is the lead time?
A: Mass production time 15-25 days.
3. Q: How long is the warranty?
A: 24 monthes from B/L. If there are any accessory problems,just
provide the photos of damaged accessory,then we will provide free
service. According to the number of products,we will provide easily
damaged accessories for free. we also can provide technical support
if you need.
4. Q: Is OEM/ODM available?
A: Yes,it is! We are manufacturer with our own R&D team, we can
customize products according to customer's drawing or requirements.
Customized services:
a. Customized color and special function.
b. Customized box.
c. Print customer's logo.
d. Your other ideas about product, we can help you design and put
them into production. The above customized services must be
confirmed before production.
5. Q: How to control the products quality?
A: Our company owns the core technology ,all kinds of products hold
CE certificate. We have professional engineers. Workers are
strictly required to make products according to the drawings. Each
process has technical instructors.The QC supervisors will regularly
inspect the production. We will do products performance tests
during production, and comprehensive quality tests when the
products is completed.
