CTS110 Sensor Measurement Range: 0-2MPa High Reliability, Good
Stability, And Low Long-Term Drift Large Working Temperature
Range:- 20℃~85℃ High Overload Voltage/Current Output
CT1110 is a ceramic capacitor pressure core, high-performance ASIC
signal conditioning core, and peripheral circuit package. Within
its range, the capacitance is proportional to the pressure and has
extremely high linearity. It has excellent compatibility with the
vast majority of pressure media, with excellent properties such as
corrosion resistance, impact vibration resistance,
anti-interference, high reliability, small fixed temperature drift,
extremely low hysteresis, and extremely low fatigue. Widely used in
the fields of pressure measurement and control, HVAC, automobiles,
water pumps, water treatment, etc.
Precautions for use
1. Do not touch the sensor diaphragm with hands or other objects,
otherwise the sensor diaphragm will be damaged.
2. The transmitter should not be overloaded, otherwise it will
cause the sensitive diaphragm of the sensor to be stressed and
deformed and drift. The pressure applied must not exceed the
transmission
The maximum overload pressure that the sensor can withstand,
otherwise the sensor will be completely damaged.
3. The supply voltage of the transmitter must be less than 36VDC
(or the highest voltage indicated on the nameplate), and the
high-voltage mains must never be connected to the meter.
4. The transmitter is composed of a circuit, and the sum of the
load resistance should be in the working area specified in the
instruction manual.
5. It is strictly forbidden to impact, knock and other violent
impacts of the transmitter during transportation, installation and
use.
6. The transmitter must be used according to the specifications,
and the different types are not interchangeable.
7. It is strictly forbidden to overvoltage during testing and use.
The transmitter range can be reduced, but it is not allowed to
exceed the upper limit of the range. The transmitter is
instantaneous
Withstands 1.25 times the upper range of overload pressure;
However, if the transmitter is subjected to more pressure than the
maximum overload pressure, the transmitter will be damaged.
8. The temperature of the medium in contact with the sensor
diaphragm must be within the allowable temperature range;
Otherwise, the transmitter will be damaged. below 0°C or special
When measuring the medium, it should be disposed of according to
the following requirements after stopping the operation: if the
measured liquid remains in the measuring chamber, the liquid will
freeze, and as a result
The transmitter can be damaged, so it is necessary to drain the
liquid to be tested after the operation has been stopped, or to
take antifreeze insulation measures.
9. In order to prevent electromagnetic radiation and lightning
attack, the transmitter housing should be grounded and connected by
shielded cable.
10. The transmitter should not be used to measure media that are
corrosive to ceramic, nitrile and stainless steel.
Parameter
| applied range | Measurement of pressure in industrial process control systems |
| Detected media | Fluid compatible with ceramic, stainless steel, and nitrile rubber |
| range | 0 ~ 500 KPa, 0 to 700 KPa, 0 to 1 MPa, 0~1.6MPa, 0 to 2 MPa et al |
| Overload pressure | 2 Admito full range |
| accuracy |
1% F.S |
| operating temperature range | -20～＋85℃ |
| Storage temperature range | -40～＋85℃ |
| Compensation temperature range | 0 ～ 50℃ |
| Effects of changes in the ambient temperature | 0.03% / ℃, a typical value |
| stability | <0.5%FS / year |
| output | Current output 4 ~ 20 m ADC two lines; voltage output 0.5-4.5V |
| Zero point deviation |
1.0% FS |
| Power Supply Voltage | 10 to 36 VDC; 12 to 36 VDC or 5VDC at voltage output |
| Main material | 304, with stainless steel |
| levels of protection |
IP65 |
