Product Description of IC695PNS001
The IC695PNS001 is a Profinet scanner module that is manufactured
by GE Fanuc / Emerson Automation. This module is a single slot wide
module, that is used to manage Profinet connections such as
communicating to remote I/O devices residing in universal I/O
backplanes, whether Series 90-30 or RX3i modules; Sending I/O data
through the Profinet network to the partner CPUs in the network;
Communicate with Human Machine Interface (HMI), Supervisory Control
and Data Acquisition (SCADA) and other similar automation
components.
The IC695PNS001 features One (1) micro USB port that is mainly used
in performing firmware upgrades. It is also equipped with Four (4)
Ethernet communication ports that primarily support Profinet
protocol. Each of the ports supports modern communication speeds
such as 10/100/1000 Mbps communication speed and supports a variety
of topologies such a Liner, Daisy-chain, Star, Ring or redundant
Ethernet media topology. Additionally, Two (2) of the IC695PNS001’s
ethernet port are Two (2) Small Form Factor (SFP) pluggable cages
that may be installed with SFP modules for converting network to
Fiber Optic media. The IC695PNS001 is designed with simplified
configuration method. I/O device name, IP address and other
parameters may be saved in an SD card and transferred to other
Profinet Scanner module by inserting the same SD card. This method
eliminates dependency with software configuration tool and
significantly decreases maintenance time.
The IC695PNS001 occupies a single slot of the backplane with status
LED indicators mounted on the module’s front panel. It has OK LED,
LAN LED, STATUS LED, CONN LED, individual PORT LEDs, ACTIVE LED and
USB LED. These LED indicators provided comprehensive overview of
the module’s operational state.
The IC695PNS001 has an internal power rating of 1.2 Amps at 3.3
Volts DC or 1.1 Amps maximum at a rated voltage of 5 Volts DC. This
module supports the Proficy Machine Edition version 8.50 or later
versions of the software. The operating temperature range for this
module is 0 to 60 degrees Celsius, and it comes with 2 SFP and 2
RJ-45 cages with the SFP devices available separately. When the
network communications are lost, the IC695PNS001 PROFINET scanner
module helps to manage the input and output states depending on the
specific configurations of a module. This module features 4
switched Ethernet ports, it supports the daisy chain, star, or ring
topologies.
Technical specifications for IC695PNS001
| Brand | GE Intelligent Platforms/GE Fanuc |
|---|
| Series | RX3i PacSystem |
|---|
| Part Number | IC695PNS001 |
|---|
| Product Line | RX3i |
|---|
| Catalog | IC695 |
|---|
| Product Type | PROFINET Scanner Module |
|---|
| Number of Slots | 1 (single slot) |
|---|
| Backplane Support | Universal |
|---|
| Protocol Support | PROFINET |
|---|
| USB Ports | 1 Micro USB |
|---|
| Internal Power at 5 V DC | 1.1 A |
|---|
| Internal Power at 3.3 V DC | 1.2 A |
|---|
| Operating Temperature | 0 to 60 degrees Celsius |
|---|
| Storage Temperature | -40 to 85 degrees Celsius |
|---|
| Ethernet Ports | Four (4) Switched Ethernet ports |
|---|
| Supported Topologies | Linear, Star, Daisy chain, Redundant Media |
|---|
| LED Indicators | OK LED, LAN LED, STATUS LED, CONN LED, ORT LEDs, ACTIVE LED, USB
LED |
|---|
The GE Fanuc / Emerson Automation IC695PNS001 is a Profinet scanner
module. This block is part of the PACSystems RX3i product family.
It connects a remote I/O rack to a Series 90-30 / RX3i module to
Profinet I/O network. This module has One (1) USB micro port for
firmware upgrade, and Four (4) Ethernet ports that support
10/100/1000 Mbps transmission rate.
