| Model | HV500 Low Voltage Engineering Single-Drive Inverter |
iInput/output
Power | Input Uin | 200V (-15%) ~240V (+10%) 3Phase , 380V (-15%) ~480V (+10%) 3Phase, |
| 500V (-15%) ~690V (+10%) 3Phase |
| Input Frequency | 50Hz/60Hz±5% |
| Unbalance Degree of Uin | ≤3% |
| Output Uout | 0V~Input Uin |
| Output Frequency | 0Hz~500Hz |
| Power range | 2.2kW~560kW |
|
Control
Performance | Motor Type | Asynchronous / Synchronous |
|
| Control Method | V/F, OLVC (Open-Loop Vector Control), CLVC (Close-Loop Vector
Control) |
| Range of Speed Regulation | 1:10 V/F, 1:100 OLVC, 1:1000 CLVC |
| Start Torque | VF: 100% (0.5Hz), OLVC: 150% (0.5Hz), CLVC: 180% (0Hz) |
| Torque Precision | ≤5%, Vector Control |
| Torque Pulsation | ≤5%, Vector Control |
| Speed Regulation Precision | OLVC 0.2%, CLVC 0.01% |
| Torque Response | <5ms, Vector Control |
| Dynamic Speed Reduction | OLVC<0.5%*s, CLVC<0.3%*s |
| Acceleration and Deceleration Time | 0.0s~3200.0s, 0.0min~3200.0min |
| Torque Lifting | 0.0%~30.0% |
| Overload | Heavy Load Application 150% 1min/5min, Light Load Application 110%
1min/5min |
| V/F Curve | Multiple ways: linear V/F curve, 5 kinds of torque reduction
characteristic curve mode (2.0 power, 1.8 power, 1.6 power, 1.4
power, 1.2 power), user-defined VF curve |
| Input Frequency Accuracy | Digital: 0.01Hz, Analog: 0.01Hz |
Control
Performance | Acceleration and Deceleration Curve | Straight, S Curve |
|
| Multiple Speed-Steps Operation | 16-Speed Steps Operation through control terminals |
| Automatic VoltageAdjustment (AVR) | Keeping the output voltage constant automatically when the grid
voltage changes within a certain range |
| Fixed Length | Setted and Fixed Length Control |
| In-build PID | It Can Easily Constructed Closed loop control system |
| Enhencement Function | Free Function Block |
| iInput/output | Set Frequency | Keyboaed, UP/DOWN Terminals, Multiple Speed-Steps Operation,
Terminals Pulsation, Com |
| Power |
| Analog Input Terminals | AI1: 0V~10V/-10V~10V, AI2: 0V~10V/0(4) mA~20mA |
| Digital Input Terminals | DI1-DI6, 6 programmable digital input terminals, optocoupler
isolation, compatible with drain/source input |
| Digital Input/Output Terminals | DIO1: Fast pulse output, normal input/output; DIO2: fast pulse
input, normal input/output |
| Anolog Output Terminals | 2 Strings 0V~10V/0 (4) mA~20mA |
| Relay Output | 2Strings Contact Type FormC |
| Motor Temperature Detection | Support PT100/PT1000/KTY84 |
| STO Interface | SIL3/PLe Safe torque shutdown function |
| Com | Com Protocol | Modbus RTU (Standard),
Profibus,CANopen,profinet,Devicenet,ControlNet |
| profinet,Devicenet,ControlNet |
| t |
| Environment | Altitude | Without Derating Operation Within 2000m Altitude; 2000m~4000m, Each
100m lifting, Derating 1% (Current) |
| Operation Temperature | -25℃~+40℃ (40℃~55℃ Derating) |
| Humidity | 15%~95%, Without Condensation |
| Vibration | 3M3, IEC60721-3-3 |
| Storage Temperature | -40℃~+70℃ |
| Operation Place | Indoor, Without direct sunlight, no flammable, corrosive gases,
liquids and conductive particles |
| Accessory | Encoding card, communication expansion card, voltage detection card |
| Protection Function | Short circuit, over current, overload, over voltage, under voltage,
phase loss, over temperature, external fault, etc. |
| Efficiency | 5.5kW~22kW: ≥93%; Above 30kW: ≥95% |
| Installation Method | Cabinet |
| Protection Degree | IP20 |
| Cooling | Forced Air Cooling |
