Laboratory Spring Hammer Impact Testing Machine Calibration Device OEM
|
...Testing Machine Calibration Device Product information: The Calibration device for spring hammer is designed and manufactured according to the standard requirements of IEC60068-2-75 and GB2423.55, it is used for the calibration of the spring hammer testers between 0 and 2 J. Because it is difficult to measure directly for the offered energy of the calibrated spring hammer, the calibration principle of this device...
Guangdong ALI Testing Equipment Co,.Ltd
|
Impact Testing Mechanical Testing Machine Calibration Device For Spring Impact Hammer As Per Annex B
|
...calibration Accuracy 0.01J Repeat accuracy ±0.01J Measurement range 0~2J Guide groove diameter 51mm The energy loss of the pendulum <0.002J Trigger distance >30mm Balance weight 2J Copper weight 1 piece Material Stainless steel Description: This device is...
Guangzhou HongCe Equipment Co., Ltd.
|
IEC60068-2-75 Environmental Testing Required Calibration Device For Spring Hammer
|
... to the standard requirements of IEC60068-2-75:1997 Annex B, IEC60068-2-63:1997 Annex A, and etc. The device is used to detect the impact energy of the Spiring Hammer Tester. When the spring hammer is released, it impacts on the pendulum rod on the...
Sinuo Testing Equipment Co. , Limited
|
Multi Purpose Impact Testing Machine Calibration Device For Spring Impact Hammer
|
Calibration Device for Spring Impact Hammer SH-7 Parameters: Accuracy: 0.01J Repeat accuracy: ±0.01J Measurement range: 0~2J Guide groove diameter: 51mm The energy loss of the pendulum: <0.002J Trigger distance: >30mm Balance weight: 2J Copper weight 1 piece Standard: IEC 60068-2-63 Annex A, IEC 60068-2-75 Annex B Application: This device is intended to verify the impact energy of spring operated impact hammers. Test......
shanghai kerang technology co ltd
|
BT Test Bar
|
Model Taper D D1 L L1 BT30-TB30-300 30 31.75 30 300 265 BT40-TB40-300 40 44.45 40 300 265 BT50-TB50-350 50 69.85 50 350 300...
Zhuzhou Bartu Electromechanical Co., Ltd.
|
0.01J IEC Test Equipment Figure B.1 Calibration Device For Spring Hammer
|
... B.1 Calibration device. Standard description: The spring hammer to be calibrated is put in the release base and is then operated three times by means of the release device; it shall not be released manually. For each operation, the striking element of the...
HJ AUTOMATIC CONTROL TECHNOLOGY CO., LTD
|
MT Magnetic Calibration Weight Lift Test Bar
|
MT Magnetic calibration 4.5kg Weight Lift Test Bar Weight Lift Test Bar designed for the calibration and certification of Magnetic Particle Inspection Yokes. Test standard:ISO 3452-3:1998(E),JB/T6066,NB/T47013-2015,ASME,GB/T26951-2011 SPECIFICATION: All ......
HUATEC GROUP CORPORATION
|
Intelligent Energy Meter Calibration Device For Single-Phase Meters Stationary Meter Test System
|
...Calibration Device for Single-Phase Meters Stationary Meter Test System Single-phase intelligent energy meter calibration device is a split/integral all-electric crimp type intelligent energy meter calibration device designed according to the requirements of relevant national standards and regulations. At the same time, it provides a perfect solution for the testing......
Guangzhou GENY Electric Co., Ltd
|
Steel Tape Calibration Equipment Steel Tape Measure Calibration Device Conventional Measuring Tools Calibrator
|
Steel Tape Calibration Equipment Steel Tape Measure Calibration Device Conventional Measuring Tools Calibrator Product Description Product Introduction The steel tape measure calibration device is designed and developed in accordance with the new JJG4-2015......
DONGGUAN LONROY EQUIPMENT CO LTD
|
Lab Testing Equipment Flame Temperature Calibration Device 50W
|
...combustion test equipment. Calibration Procedure Position the copper block 10±1mm above the needle flame burner. Ignite the flame; the time for the copper block temperature to ......
Guangdong Haida Equipment Co., Ltd.
|