| Sign In | Join Free | My burrillandco.com |
|
Intelligent Vortex Flowmeter With Flange Compressed Air Nitrogen Steam Gas, Liquid High Precision High precision, generally up to 1% R, 0.5% R, and high-precision models up to 0.2% R; Good repeatability, ...
The Proline Prowirl F 200 (7F2C) is a high-precision vortex flowmeter developed by Endress+Hauser, designed for accurate measurement of wet, saturated, and superheated steam, as well as gases and liquids. It is...
Product Description: Stainless steel folding filter elements have high resistance to intergranular corrosion and good corrosion resistance to some organic and inorganic acids (especially in oxidizing media). Th...
304 stainless steel pipe round pipe 316 seamless pipe Precision pipe thick wall zero cut white stainless steel hollow All the two ends of the opening and hollow section, and its length and section circumference...
..., Products: steam turbine rotor forging,Alloy steel steam turbind rotor,main shaft of low pressure steam turbine,main shaft of middle pressure steam turbine,main shaft of high pressure steam turbine,main sha...
25Cr2Ni4MoV Blower Shaft Forging Alloy Steel Mechanical High Strength Products: Steam turbine rotor forging,alloy steel steam turbine rotor,blower main shaft,blower rotor,solid forging rotor,welded rotor Produc...
... least two levels of steam turbine: high pressure turbine and low pressure turbine. 2. High pressure steam turbine output steam, commonly known as cold reheat steam, has lower pressure and temperature of mai...
Steam Turbine Motor 30KW 12000RPM Servo Brushless Electrical PM High Speed Motor New Design Product Feature 1. Suitable for the ......
Steam Turbine Motor 45KW 2500RPM Servo 3 Phase Brushless Permanent Magnetic Motor for Industrial Usage Product Feature 1. Permanent Magnetic synchronous low-speed motor is suitable for 2500 RPM low-speed applic...
Steam Turbine Motor 55KW 2500RPM AC Synchronous Reluctance Permanent Magnetic Directly Driving Motor Product Feature Permanent Magnetic synchronous low-speed motor is suitable for 2500 RPM low-speed application...
... governor to control speeds of a water turbine In steam turbines, the steam turbine governing is the procedure of monitoring and controlling the flow rate of steam into the turbine with the objective of main...
...generation, steam engines, and in processes such as steam reforming. Reheater Power plant furnaces may have a reheater section containing tubes heated by hot flue gases outside the tubes. Exhaust steam from ...
...steam turbine rapid cooling equipment simple operation Product description This device is a special supporting equipment for accelerated cooling with compressed air after the large-capacity turbine is shut d...
...steam is reheated to improve cycle efficiency after high pressure part of the steam turbine. Reheater system increase boiler LP – steam, which is turbine’s IP-steam (IP = IntermediatePressure), temperature a...
...uses waste heat (generally from Gas Turbines) to generate steam. Therefore, HRSGs are generally attached to the exhaust of Gas Turbines. They are commonly used in Combined Cycle Power Plants where both Gas a...
...Steam Generator for Industry Product Descripton Heat Recovery Steam Generators are a type of Waste Heat Recovery unit which uses waste heat (generally from Gas Turbines) to generate steam. Therefore, HRSGs a...
...uses waste heat (generally from Gas Turbines) to generate steam. Therefore, HRSGs are generally attached to the exhaust of Gas Turbines. They are commonly used in Combined Cycle Power Plants where both Gas a...
...Key Applications : Steam Turbine Generator, Condenser, Cooling Tower, Reactor Building, Turbine Building, Reactor Facility Grounds & BOP, Steam Turbine, Gas Turbine, Heat Recovery Steam Generator, Balance Of...
...Key Applications : Steam Turbine Generator, Condenser, Cooling Tower, Reactor Building, Turbine Building, Reactor Facility Grounds & BOP, Steam Turbine, Gas Turbine, Heat Recovery Steam Generator, Balance Of...
...generally from Gas Turbines) to generate steam. Therefore, HRSGs are generally attached to the exhaust of Gas Turbines. They are commonly used in Combined Cycle Power Plants where both Gas and Steam turbines...