| Sign In | Join Free | My burrillandco.com |
|
BS 476 Part 7 Flammability Testing Equipment / Surface Flame Spread Test Apparatus Introduction: BS 476 Part 7 specifies a method of test for measuring the lateral spread of flame along the surface of the speci...
IEC 60695-2-10 Glow Wire Test Flammability Testing Apparatus Product information: The Glow Wire Tester is a professional fire hazard testing device designed primarily according to international standards IEC 60...
... designed to assess the flammability of material surfaces. It primarily follows ASTM E162, "Standard Test Method for Flammability of Surfaces of Materials Using Radiant Heat Sources," and ASTM D3675, "Standa...
... with a small flame in a normal combustion environment to determine the flammability of building products. The flammability test furnace for building materials uses the German Kleinbrenner (Kleinbrenner) pri...
...figure 21 clause 23.4, which is used to process the flexing test for the flexible cable of non-rewirable plugs and non-rewirable portable socket-outlets. Equipment characteristics: The test times (up to 9999...
...Test Apparatus For Heating Resistance In Hot Conditions Standards For Coupler Heating Test Apparatus: IEC60320-1:2021 "Appliances couplers for household and similar general purposes- Part1:General requi...
... to IEC 60884-1: 2022 Annex C alternative gripping tests figure C.2, the reference plug as per C.1 also below shown: Technical Parameters For Plug Gripping Test Apparatus: Item Specifications A reference plu...
... 110, Figure 111 and Table 114. Product overview Samples and restrictions: Electric vehicle AC and DC charging station Test purpose: The flexible cord anchorage of the appliance shall relieve conductors at t...
Offset Misalignment Test Apparatus EV Charging Interface Misalignment Tester Complied Standards & Clauses This test equipment conforms to UL2552-2022, clause 54C.3 and Figure 54C.2, IEC62196-1. Equipment Overvi...
...-2-10, IEC60695-2-11, IEC60695-2-12 IEC60695-2-13. It also conforms to the standard requirement of UL746A. This device simulates the thermal stress test of glowing component or heat source like overload resi...
...Test Apparatus Product information: It is used for resistance test to torque of cookware handle. The torsion deformation of the handle in all directions does not exceed 10°. The degree of deformation cannot ...
...Resistance Test Apparatus Product information: It is used for testing resistance to pull on cookware handles. When the handle is subjected to horizontal pull, the degree of deformation cannot affect the func...
... 62196-1:2014 clause 17.2. It is used to check the maximum force required when the test plug is withdrawn from the socket-outlet or vehicle connector and the minimum force required when the single-stage pin ...
...Testing Apparatus For Charging Plug Product information: The test equipment is used to check whether a plug or vehicle connector shall have adequate resistance to damage from being driven over by a vehicle, ...
...Test Apparatus Product information: The testing system is required by IEC 62368-1:2018 clause Y.5, etc. It is used to verify the protective performance of the enclosure for electronic and electrical products...
...Test Device Applied standard and clauses: This hydraulic pressure test apparatus is required by IEC 60335-2-5 cl.22.101,IEC 60335-2-7 cl.22.101 , IEC 60335-2-21/35 22.47 & 22.103 , IEC 60335-2-24 cl.22.7, et...
IEC 60309-1 Plugs And Vehicle Connectors Cable Anchorage Pull Force And Torque Test Apparatus Product information: This pull force and torque test equipment is used to test the vehicle plugs, and socket-outlets...
...-1, mainly used for the lamps adjustment devices’ torsion, and bending test of the table lamps, floor lamps and the lamps which are for professional use (such as a plotter lamps). To verify adjusting devices...
BS EN 12983-1 Pencil Hardness Test Apparatus For Exterior Organic Coatings Test Scratch Resistance Product overview: The equipment is complied with BS EN 12983-1 clause 8.4.2 ,8.4.3 and Appendix K. The device u...
IEC 60335-1 Needle Flame Test Apparatus For Test Flammability And Fire Resistance Of Materials Product overview: The Needle Flame Tester consists of a 0.9mm needle-shaped burner that tilts with the angel of 45...