| Sign In | Join Free | My burrillandco.com |
|
... Drivers 1. Adoption of 32-bit DSP, pure sine wave subdivision technology 2. Low-noise, low-vibration and low temperature rising 3. Voltage 24-50VDC 4. With 8 stalls output current setting, peak current5.6A ...
... Drivers 1. Adoption of 32-bit DSP, pure sine wave subdivision technology 2. Low-noise, low-vibration and low temperature rising 3. Voltage 24-50VDC 4. With 8 stalls output current setting, peak current5.6A ...
...Driver Datachable LED Driver Long Detection Range Dimmable Sensor Datachable LED Driver Sensor Features: Detection area, hold time, stand-by period, stand-by dimming level, daylight sensor and mode can be pr...
... setting Open/closed loop control Motor torque holding Restart Various alarm indications Internal potentiometer and RV speed ......
...Setting LED Driver Microwave Motion Sensor For Tri-proof Lamps Features: Wide detection area, range up to 14m in diameter. Detection area, hold time, stand-by period, stand-by dimming level, daylight sensor ...
...Driver DIP Switch Setting Isolated Solution Sensor DIP Seitch Setting 36W Microwave Movement Sensor Features: High frequency 5.8GHz, input power 45W Max, output power 36W Max. Dimming function and DIP switch...
...driver Features 1. Adoption of bipolar constant-current chopper technology 2. Low-noise, low-vibration and low temperature rising 3. Voltage 80-110VAC 4. With 16 stalls output current setting, current 0.38-6...
... 18-40VDC 4. With 8 stalls output current setting, current range 0.9-3.0A 5. With 7 stalls microstep subdivision setting 6. Automatic Half current, motor wires misconnected protection 7. Internal optical iso...
...driver Features 1. 2phase stepper driver, adoption of bipolar constant-current chopper technology 2. Low-noise, low-vibration and low temperature rising 3. Voltage 24-50VDC 4. With 8 stalls output current se...
.... 2. Low-noise, low-vibration and low temperature rising 3. Voltage 18~50V DC 4. With 8 stalls output current setting, peak current 4.5A 5. With 14 stalls microstep subdivision setting 6. Automatic Half curr...
Fire Fighting Pump Set Use Diesel Engine Driver , Ul Fire Pump NFPA20 Standard ENGINE RATINGS BASELINES Fire fighting engine: It is a kind of engine in accordance with fire fighting standard. Compared with norm...
2 Stage FM Approved Vertical Turbine Fire Pump Set With Electric Motor Driver These pumps are helpful in areas where water is scarce, but also when installing an above-ground water storage tank is not desirable...
18M Excavator Mounted Hydraulic Vibrating Pile Driver - Comprehensive Product Introduction Core Keywords Pile Driver 18M Excavator Mounted Pile Driver 3300rpm Vibrating Pile Driver VIBRA Brand Pile Driver Hydra...
...-noise, low-vibration and low temperature rising 3. Voltage 36-110VDC,24-80VAC 4. With 8 stalls output current setting,peak current 2.4-7.2A 5. With 16 stalls microstep subdivision setting. 6. Automatic Half...
2 x 25W IP20 Dimmable LED Driver 250mA - 700mA For LED Down Light Description: 1, Two output channels for different applications. Use DIP switch for output current setting, each channel supplies selectable curr...
...Driver for LED panel light Description: 1, Press-in terminals in primary and secondary side, easy assembly. 2, Long life span 50,000h, 5 years guaranty. 3, with 1-10V and push in PRI and SEC side. 4, no fli...
MLC16C-P Sensor driver 16w 300mA/350mA integrated with sensor dimming function Description 1, Output power: 16w max. 2, Output current: 300mA,350mA set via dip sw.itches. 3, Output voltage: 28-48Vdc. 4, Working...
...Driver Description: MS01 work with ML30C-PV to provides an energy saving without sacrificing visual comfort Output current to load selectable from 250mA to 700mA With ambient light dependent control. Directl...
...Driver Ceiling Mount With MW Sensor Description: MS01 Directly connected to 1-10V interface of ML50C-PV MS01 work with ML50C-PV and MC008S to provides auto on – off and daylight harvesting function Luminaire...
... Output current to load selectable from 250mA to 700mA With ambient light dependent control. Directly connected to 1-10V interface. Simple setting of the target light level by mean of potentiometer MC008S wi...