| Sign In | Join Free | My burrillandco.com |
|
...Resistor installed, to protect operator from accidental contact with equipment line voltage - 4mm buckle are stamped, stainless steel back plate - Even if one dual wire wrist strap conductor is severed, oper...
...Resistor installed, to protect operator from accidental contact with equipment line voltage - 4mm buckle are stamped, stainless steel back plate - Even if one dual wire wrist strap conductor is severed, oper...
... wristband with 10mm snap 4. 1 Meg Ohm resistor for added safety 5. Sets with 6' or 10' coil cord 6. Two snaps Detailed description HZ-41101Economical Type Antistatic Elastic Wrist Strap An antistatic wrist ...
... industrial engineering environments. Metal alloy titanium solution grounding electrode with high resistance to the corrosive environment. A high precision NTC10K temperature resistor for temperature detecti...
..., resistance strip are widely used in industrial furnace, civil electrical appliances, rail transit braking resistor, central grounding resistance, automobile exhaust purification honeycomb carrier and other...
... (2.8mA typical). - ±15kV ESD protection on RS-485 pins. - Slew-rate-limited driver eliminates data-dependent ground bounce. - Internal 1/5th bias resistors for RS-485 operation. - Hot-swap, hot...
... swing Input voltage range extends 150 mV below ground (single supply) Low power, 550 μA maximum supply current Gain set with one external resistor Gain range: 1 to 1000 High accuracy dc performance 0.10% ga...
...-to-rail output swing Input voltage range extends 150 mV below ground (single supply) Low power, 550 μA maximum quiescent current Gain set with one external resistor Gain range: 1 to 1000 High accuracy dc pe...
... part count low, but the addition of an external resistor and capacitor between pins 1 and 8 will increase the gain to any value up to 200. The inputs are ground referenced while the output is automatically ...
... • No switch-on/switch-off plops • High supply voltage ripple rejection • Protected against electrostatic discharge • Outputs short-circuit safe to ground, VCC and...
...Ground Bounce) <0.8 V at VCC = 3.3 V, TA = 25°C Support Unregulated Battery Operation Down to 2.7 V Ioff and Power-Up 3-State Support Hot Insertion Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors Latch-Up Performance Exceeds 500 mA...
...cell phones, notebook computers, PDAs, and other systems where current monitoring is crucial. High-side current monitoring does not interfere with the ground path of the battery charger making the MAX4073 pa...
... and benefits 8 channels for RTD (Pt100, Cu10, Ni100 and Ni120 and resistor) inputs 3-wire connection to RTDs 14 Bit resolution Inputs are monitored for open-circuit, shortcircuit and has a input grounded se...
... distinguishing feature lies in the high output impedance, granting users the freedom to select a sampling resistor tailored to their needs without jeopardizing system stability. Specifically crafted for mea...
...Ground Resistance:106Ω ~ 108Ω ♦ Dissipation Time:0.1S ♦ Color: Red,Yellow,Blue,Black Surface Resistance: > 1M ohms Contact: 360 degrees around wrist Snap: 10mm Snap release: 1 to 5 pounds Back plate: stainle...
...connected to the grounding wire through a button, creating an electrostatic discharge path that safely removes static charges from the body. Each cord is equipped with a built-in 1MΩ safety resistor to ensur...
...connected to the grounding wire through a button, creating an electrostatic discharge path that safely removes static charges from the body. Each cord is equipped with a built-in 1MΩ safety resistor to ensur...
...connected to the grounding wire through a button, creating an electrostatic discharge path that safely removes static charges from the body. Each cord is equipped with a built-in 1MΩ safety resistor to ensur...
...Ground Resistance:106Ω ~ 108Ω ♦ Dissipation Time:0.1S ♦ Color: Red,Yellow,Blue,Black Surface Resistance: > 1M ohms Contact: 360 degrees around wrist Snap: 10mm Snap release: 1 to 5 pounds Back plate: stainle...
... through the neutral pin. This was a legal grounding method under the National Electrical Code for electric ranges and electric clothes dryers from the 1947 to the 1996 edition. Since North American dryers a...