Copper Customized Wire Drawing Machine , Wire Drawing Machine With Automatic Double Spooler

HXE-17DWT Copper fine wire drawing machine with annealer

I. Application

HXE-17DWT Fine copper wire drawing machine with annealer and double spooler is used to draw and anneal single bare copper wire from 1.8mm to 0.3mm-0.7mm.

II. Components

III. Main Technical parameters

1. Usage: Copper wire drawing and annealing

2. Inlet diameter: 1.8mm

3. Outlet diameter: 0.3mm-0.7mm

4. Max. mechanical speed: 1500m/min.

5. Dies: 17 dies

6. Slip ratio: 17.5%, Finished capstan slip ratio: 10%

7. Main motor: AC 3 Phase 22KW, Inverter control

8. Spool motor: AC 3 Phase 2.2KW*2, Inverter control

9. Spool size: Diameter 200mm/Max (Customize)

10. Capstans: Ceramic plasma, Drawing capstan 316mm, Final capstan 268mm

11. Capstan lubrication: Water pipe spray

12. Traversing: 110W synchronous motor,transmission by timing belts.

13. Brake: 20KG-M Electromagnetic brake

14. Air pressure: 4-6kg/cm2

15. Annealing volt: 60V

16. Annealing current: 600A

17. Annealing motor power: 36KVA

18. Power source:380V/50Hz (customize)

19. Tension control: Annealer & Spooler Tension control by Swing arms, Air pressure auto adjust.

20. Transmission part; The main drive is mainly driven by a toothed belt (inlet), and the annealed part is driven by a flat belt.

21. Structure:Steel plate welding annealing treatment, integrated processing.

22. Bobbin loading and unloading type: Double end thimbles, trolleys are attached.

IV. Attention

4-1. If wire breaks, will stop automatically, and the Fault Indicator light will open.

After connect the wire, press the Fault Reset button(Yellow button) and the On button (Green button), to run the machine again.

4-2. Press Emergency Stop button(Red button) to shut down the machine immediately.

After solve, press the button again to run the machine.

4-3. After set the Length-counter, the machine will stop automatically when reach the length set.

After change the Spool, please press the Length Reset button(Yellow button) and the Spool Reset button(Yellow button) to run the machine again.

4-4. After the machine stop(no running at all), then switch the Pump switch to stop the lubrication.

4-5. Do not touch the wire in the Annealing section.

4-6. After shut down the machine, need at least 30 seconds to restart the machine.

4-7. Wire often breaks, adjust the speed, balance arm, check the dies are clean or not.

4-8. If has scratch on the surface of the wire, check the capstans on the Take-up part. Check the drawing capstans.

V. Machine maintenance and precautions

1. Make sure the machine and the capstans clean, no scrap, no break wire.

2. Make sure the Take-up part clean.

3. Electrical cabinet should be closed.

4. Change belts if worn out.

5. Only qualified electrical technician can repair the electrical part.

6. Never change the Inverter parameter.

7. If something wrong with the machine that can`t solve, please contact the supplier first.

Do not open the machine without consulting to the supplier.

8. Put lubrication oil to the parts regularly, to make sure all parts running fluently. After running 1000 hours, clean all the bearings.

9. Annealed nickel belt and Annealing carbon brush are consuming parts. If spark happens a lot on the annealing capstans, then should change the nickel belt. If the carbon is going to run out, then need to change a new set.

      Suzhou Hengxie Machinery Co., Ltd was established in 2005, a total professional in drawing machine field, specialized in copper and aluminium wire drawing machines. Located in Suzhou City, very close to Shanghai, we share a convenient transportation and the most successful working environment.

Our 6,700 square meters of land allows producing a wide range of equipment, developing and researching new products. We always strive to introduce the latest international techniques to update our products.

With management concept of “Excellent quality, Reasonable prices, Superior services”, our hope is to not only meet our customers` expectations but to exceed them.

Here are the machines we have: Copper&Aluminium Rod Breakdown machine, Large and intermediate wire drawing machine with online annealer, Intermediate wire drawing machine, Intermediate wire drawing machine with online annealer, Fine wire drawing machine, Fine wire drawing machine with online annealer, Customized fine wire drawing machine with annealer, Super fine wire drawing machine. As long as we talk, we can always meet your detail requirements.

Our market includes both domestic and overseas. Such as Bangladesh, Egypt, Iran, Malaysia, Syria, Algeria, Kenya, Turkey, South Africa, Latin America and so on.

With the concept of “Stable quality and mutual development”, Hengxie welcome all customers from the world to create a sincere cooperation and win-win benefit in the future.